- 您現在的位置：買賣IC網 > PDF目錄358933 > LPC47B27X (SMSC Corporation) Round, Jacket Mass-Terminated Cable, 3659/26 28 AWG, .050 (1.27) PDF資料下載
參數資料
| 型號： | LPC47B27X |
| 廠商： | SMSC Corporation |
| 英文描述： | Round, Jacket Mass-Terminated Cable, 3659/26 28 AWG, .050 (1.27) |
| 中文描述： | 100引腳增強型超的I / O LPC接口控制器 |
| 文件頁數： | 16/196頁 |
| 文件大?。?/td> | 1200K |
| 代理商： | LPC47B27X |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁
SMSC LPC47B27x
- 16 -
Rev. 08-10-04
DATASHEET
Indication of 32kHz Clock
There is a bit to indicate whether or not the 32kHz clock input is connected to the LPC47B27x. This bit is located at
bit 0 of the CLOCKI32 register at 0xF0 in Logical Device A. This register is powered by VTR and reset on a VTR
POR.
Bit[0] (CLK32_PRSN) is defined as follows:
0=32kHz clock is connected to the CLKI32 pin (default)
1=32kHz clock is not connected to the CLKI32 pin (pin is grounded).
Bit 0 controls the source of the 32kHz (nominal) clock for the CIR logic, fan tachometer logic, WDT, the LED blink
logic and the “wake on specific key” logic. When the external 32kHz clock is connected, that will be the source for the
CIR logic, fan tachometer, LED and “wake on specific key” logic. When the external 32kHz clock is not connected,
an internal 32kHz clock source will be derived from the 14MHz clock for the CIR logic, fan tachometer, WDT, LED
and “wake on specific key” logic.
The following functions will not work under VTR power (VCC removed) if the external 32kHz clock is not connected.
These functions will work under VCC power even if the external 32kHz clock is not connected.
CIR wakeup
Wake on specific key
LED blink
Fan tachometer
WDT
Trickle Power Functionality
When the LPC47B27x is running under VTR only (VCC removed), PME wakeup events are active and (if enabled)
able to assert the nIO_PME pin active low. The following lists the wakeup events:
UART 1 Ring Indicator
UART 2 Ring Indicator
Keyboard data
Mouse data
CIR
Wake on Specific Key Logic
Fan Tachometers (Note)
GPIOs for wakeup. See below.
Note. The Fan Tachometers can generate a PME when VCC=0. Clear the enable bits for the fan tachometers
before removing fan power.
The following requirements apply to all I/O pins that are specified to be 5 volt tolerant.
I/O buffers that are wake-up event compatible are powered by VCC. Under VTR power (VCC=0), these pins may
only be configured as inputs. These pins have input buffers into the wakeup logic that are powered by VTR.
I/O buffers that may be configured as either push-pull or open drain under VTR power (VCC=0), are powered by
VTR. This means, at a minimum, they will source their specified current from VTR even when VCC is present.
The GPIOs that are used for PME wakeup as input are GP10-GP17, GP20-GP22, GP24-GP27, GP30-GP34, GP41,
GP43, GP50-GP57, GP60, GP61. These GPIOs function as follows (with the exception of GP53, GP60 and GP61 -
see below):
Buffers are powered by VCC, but in the absence of VCC they are backdrive protected (they do not impose a load
on any external VTR powered circuitry). They are wakeup compatible as inputs under VTR power. These pins
have input buffers into the wakeup logic that are powered by VTR.
All GPIOs listed above are for PME wakeup as a GPIO (or alternate function) excluding GP34, which has the IRRX2
function and is used for CIR PME wakeup only. Note that GP32 and GP33 cannot be used for wakeup under VTR
power (VCC=0) since these are the fan control pins which come up as outputs and low following a VCC POR and
Hard Reset. GP53 cannot be used for wakeup under VTR power since this is the TXD2(IRTX) pin which comes up
as output and low following a VTR POR, a VCC POR and Hard Reset. GP43 reverts to the basic GPIO function
when VCC is removed from the part, but its programmed input/output, invert/non-invert and output buffer type is
retained.
相關PDF資料 |
PDF描述 |
|---|---|
| LPC47B34X | 128 Pin Enhanced Super I/O with LPC Interface for Consumer Applications |
| LPC47B37X | 100 Pin Enhanced Super I/O for LPC Bus with SMBus Controller for Commercial Applications |
| LPC47M14X-NC | 128 PIN ENGANCED SUPER I/O CONTROLLER WITH AN LPC INTERFACE AND USB HUB |
| LPC47M14Y-NC | 128 PIN ENGANCED SUPER I/O CONTROLLER WITH AN LPC INTERFACE AND USB HUB |
| LPC47M14Z-NC | 128 PIN ENGANCED SUPER I/O CONTROLLER WITH AN LPC INTERFACE AND USB HUB |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LPC47B34X | 制造商:SMSC 制造商全稱:SMSC 功能描述:128 Pin Enhanced Super I/O with LPC Interface for Consumer Applications |
| LPC47B351-NC | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| LPC47B357-NC | 制造商:SMSC 功能描述:ELECTRONIC COMPONENT |
| LPC47B373QFP | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:SMSC 功能描述: |
| LPC47B373QFP WAF | 制造商:SMSC 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。