參數資料
型號: LPC2478FBD208
廠商: NXP Semiconductors N.V.
元件分類: 數學處理器
英文描述: Single-chip 16-bit-32-bit micro; 512 kB flash, Ethernet, CAN, LCD, USB 2.0 device-host-OTG, external memory interface
封裝: LPC2478FBD208<SOT459-1 (LQFP208)|<<http://www.nxp.com/packages/SOT459-1.html<1<Always Pb-free,;LPC2478FET208<SOT950-1 (TFBGA208)|<<http://www.nxp.com/packages/SOT950-1.ht
文件頁數: 82/93頁
文件大?。?/td> 751K
代理商: LPC2478FBD208
LPC2478
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 3 — 12 September 2011
82 of 93
NXP Semiconductors
LPC2478
Single-chip 16-bit/32-bit microcontroller
In slave mode the input clock signal should be coupled by means of a capacitor of 100 pF
(
Figure 27
), with an amplitude between 200 mV (RMS) and 1000 mV (RMS). This
corresponds to a square wave signal with a signal swing of between 280 mV and 1.4 V.
The XTAL2 pin in this configuration can be left unconnected.
External components and models used in oscillation mode are shown in
Figure 28
and in
Table 23
and
Table 24
. Since the feedback resistance is integrated on chip, only a crystal
and the capacitances C
X1
and C
X2
need to be connected externally in case of
fundamental mode oscillation (the fundamental frequency is represented by L, C
L
and
R
S
). Capacitance C
P
in
Figure 28
represents the parallel package capacitance and should
not be larger than 7 pF. Parameters F
OSC
, C
L
, R
S
and C
P
are supplied by the crystal
manufacturer.
Table 23.
Fig 28. Oscillator modes and models: oscillation mode of operation and external crystal
model used for C
X1
/C
X2
evaluation
Recommended values for C
X1
/C
X2
in oscillation mode (crystal and external
components parameters): low frequency mode
Fundamental oscillation
frequency F
OSC
capacitance C
L
1 MHz to 5 MHz
10 pF
20 pF
30 pF
5 MHz to 10 MHz
10 pF
20 pF
30 pF
10 MHz to 15 MHz
10 pF
20 pF
15 MHz to 20 MHz
10 pF
Crystal load
Maximum crystal
series resistance R
S
< 300
< 300
< 300
< 300
< 200
< 100
< 160
< 60
< 80
External load
capacitors C
X1
/C
X2
18 pF, 18 pF
39 pF, 39 pF
57 pF, 57 pF
18 pF, 18 pF
39 pF, 39 pF
57 pF, 57 pF
18 pF, 18 pF
39 pF, 39 pF
18 pF, 18 pF
002aag469
LPC2xxx
XTAL1
XTAL2
CX2
CX1
XTAL
=
CL
CP
RS
L
相關PDF資料
PDF描述
LPC2478FET208 Single-chip 16-bit-32-bit micro; 512 kB flash, Ethernet, CAN, LCD, USB 2.0 device-host-OTG, external memory interface
LPC2917FBD144 ARM9 microcontroller with CAN and LIN
LPC2919FBD144 ARM9 microcontroller with CAN and LIN
LPC2921FBD100 ARM9 microcontroller with CAN, LIN, and USB
LPC2923FBD100 ARM9 microcontroller with CAN, LIN, and USB
相關代理商/技術參數
參數描述
LPC2478FBD208,551 功能描述:ARM微控制器 - MCU LCD CONT/ETHNET USB/512K FL RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT
LPC2478FBD208,551 制造商:NXP Semiconductors 功能描述:IC, 32BIT MCU, 72MHZ, LQFP-208
LPC2478FBD208551 制造商:NXP Semiconductors 功能描述:MCU ARM7 208LQFP
LPC2478FBD208551 制造商:NXP Semiconductors 功能描述:IC 32BIT MCU 72MHZ LQFP-208
LPC2478FET,208 制造商:NXP Semiconductors 功能描述: