- 您現在的位置：買賣IC網 > PDF目錄385497 > LPC2468FET208 (NXP Semiconductors N.V.) Single-chip 16-bit-32-bit micro; 512 kB flash, Ethernet, CAN, ISP-IAP, USB 2.0 device-host-OTG, external memory interface PDF資料下載
參數資料
| 型號： | LPC2468FET208 |
| 廠商： | NXP Semiconductors N.V. |
| 元件分類： | 數學處理器 |
| 英文描述： | Single-chip 16-bit-32-bit micro; 512 kB flash, Ethernet, CAN, ISP-IAP, USB 2.0 device-host-OTG, external memory interface |
| 封裝： | LPC2468FBD208<SOT459-1 (LQFP208)|<<http://www.nxp.com/packages/SOT459-1.html<1<Always Pb-free,;LPC2468FET208<SOT950-1 (TFBGA208)|<<http://www.nxp.com/packages/SOT950-1.ht |
| 文件頁數： | 44/85頁 |
| 文件大小： | 682K |
| 代理商： | LPC2468FET208 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁當前第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁
LPC2468
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 6.1 — 6 September 2011
44 of 85
NXP Semiconductors
LPC2468
Single-chip 16-bit/32-bit micro
7.26 System control
7.26.1
Reset
Reset has four sources on the LPC2468: the RESET pin, the Watchdog reset, power-on
reset, and the BrownOut Detection (BOD) circuit. The RESET pin is a Schmitt trigger input
pin. Assertion of chip Reset by any source, once the operating voltage attains a usable
level, starts the Wake-up Timer (see description in
Section 7.25.3 “Wake-up timer”
),
causing reset to remain asserted until the external Reset is de-asserted, the oscillator is
running, a fixed number of clocks have passed, and the flash controller has completed its
initialization.
When the internal Reset is removed, the processor begins executing at address 0, which
is initially the Reset vector mapped from the Boot Block. At that point, all of the processor
and peripheral registers have been initialized to predetermined values.
7.26.2
Brownout detection
The LPC2468 includes 2-stage monitoring of the voltage on the V
DD(DCDC)(3V3)
pins. If this
voltage falls below 2.95 V, the BOD asserts an interrupt signal to the Vectored Interrupt
Controller. This signal can be enabled for interrupt in the Interrupt Enable Register in the
VIC in order to cause a CPU interrupt; if not, software can monitor the signal by reading a
dedicated status register.
The second stage of low-voltage detection asserts Reset to inactivate the LPC2468 when
the voltage on the V
DD(DCDC)(3V3)
pins falls below 2.65 V. This Reset prevents alteration of
the flash as operation of the various elements of the chip would otherwise become
unreliable due to low voltage. The BOD circuit maintains this reset down below 1 V, at
which point the power-on reset circuitry maintains the overall Reset.
Both the 2.95 V and 2.65 V thresholds include some hysteresis. In normal operation, this
hysteresis allows the 2.95 V detection to reliably interrupt, or a regularly-executed event
loop to sense the condition.
7.26.3
Code security (Code Read Protection - CRP)
This feature of the LPC2468 allows user to enable different levels of security in the system
so that access to the on-chip flash and use of the JTAG and ISP can be restricted. When
needed, CRP is invoked by programming a specific pattern into a dedicated flash location.
IAP commands are not affected by the CRP.
There are three levels of the Code Read Protection.
CRP1 disables access to chip via the JTAG and allows partial flash update (excluding
flash sector 0) using a limited set of the ISP commands. This mode is useful when CRP is
required and flash field updates are needed but all sectors can not be erased.
CRP2 disables access to chip via the JTAG and only allows full flash erase and update
using a reduced set of the ISP commands.
Running an application with level CRP3 selected fully disables any access to chip via the
JTAG pins and the ISP. This mode effectively disables ISP override using P2[10]/EINT0
pin, too. It is up to the user’s application to provide (if needed) flash update mechanism
using IAP calls or call reinvoke ISP command to enable flash update via UART0.
相關PDF資料 |
PDF描述 |
|---|---|
| LPC2470FBD208 | Flashless 16-bit-32-bit microcontroller; Ethernet, CAN, LCD, USB 2.0 device-host-OTG, external memory interface |
| LPC2470FET208 | Flashless 16-bit-32-bit microcontroller; Ethernet, CAN, LCD, USB 2.0 device-host-OTG, external memory interface |
| LPC2478FBD208 | Single-chip 16-bit-32-bit micro; 512 kB flash, Ethernet, CAN, LCD, USB 2.0 device-host-OTG, external memory interface |
| LPC2478FET208 | Single-chip 16-bit-32-bit micro; 512 kB flash, Ethernet, CAN, LCD, USB 2.0 device-host-OTG, external memory interface |
| LPC2917FBD144 | ARM9 microcontroller with CAN and LIN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LPC2468FET208,551 | 功能描述:ARM微控制器 - MCU ARM7 512KF/USBH/ENET RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT |
| LPC2468FET208/CP3E | 制造商:NXP Semiconductors 功能描述:- Trays |
| LPC2468FET208551 | 制造商:NXP Semiconductors 功能描述:IC 32BIT MCU 72MHZ TFBGA-208 |
| LPC2470 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Flashless 16-bit/32-bit microcontroller; Ethernet, CAN, LCD, USB 2.0 device/host/OTG, external memory interface |
| LPC2470_11 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Flashless 16-bit/32-bit microcontroller; Ethernet, CAN, LCD, USB 2.0 device/host/OTG |
發布緊急采購，3分鐘左右您將得到回復。