參數資料
型號： LPC2468FBD208
廠商： NXP Semiconductors N.V.
元件分類： 數學處理器
英文描述： Single-chip 16-bit-32-bit micro; 512 kB flash, Ethernet, CAN, ISP-IAP, USB 2.0 device-host-OTG, external memory interface
封裝： LPC2468FBD208<SOT459-1 (LQFP208)|<<http://www.nxp.com/packages/SOT459-1.html<1<Always Pb-free,;LPC2468FET208<SOT950-1 (TFBGA208)|<<http://www.nxp.com/packages/SOT950-1.ht
文件頁數： 42/85頁
文件大小： 682K
代理商： LPC2468FBD208
LPC2468
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 6.1 — 6 September 2011
42 of 85
NXP Semiconductors
LPC2468
Single-chip 16-bit/32-bit micro
7.25.4
Power control
The LPC2468 supports a variety of power control features. There are four special modes
of processor power reduction: Idle mode, Sleep mode, Power-down mode, and Deep
power-down mode. The CPU clock rate may also be controlled as needed by changing
clock sources, reconfiguring PLL values, and/or altering the CPU clock divider value. This
allows a trade-off of power versus processing speed based on application requirements.
In addition, Peripheral power control allows shutting down the clocks to individual on-chip
peripherals, allowing fine tuning of power consumption by eliminating all dynamic power
use in any peripherals that are not required for the application. Each of the peripherals
has its own clock divider which provides even better power control.
The LPC2468 also implements a separate power domain in order to allow turning off
power to the bulk of the device while maintaining operation of the RTC and a small SRAM,
referred to as the Battery RAM.
7.25.4.1
Idle mode
In Idle mode, execution of instructions is suspended until either a Reset or interrupt
occurs. Peripheral functions continue operation during Idle mode and may generate
interrupts to cause the processor to resume execution. Idle mode eliminates dynamic
power used by the processor itself, memory systems and related controllers, and internal
buses.
7.25.4.2
Sleep mode
In Sleep mode, the oscillator is shut down and the chip receives no internal clocks. The
processor state and registers, peripheral registers, and internal SRAM values are
preserved throughout Sleep mode and the logic levels of chip pins remain static. The
output of the IRC is disabled but the IRC is not powered down for a fast wake-up later. The
32 kHz RTC oscillator is not stopped because the RTC interrupts may be used as the
wake-up source. The PLL is automatically turned off and disconnected. The CCLK and
USB clock dividers automatically get reset to zero.
The Sleep mode can be terminated and normal operation resumed by either a Reset or
certain specific interrupts that are able to function without clocks. Since all dynamic
operation of the chip is suspended, Sleep mode reduces chip power consumption to a
very low value. The flash memory is left on in Sleep mode, allowing a very quick wake-up.
On the wake-up from Sleep mode, if the IRC was used before entering Sleep mode, the
code execution and peripherals activities will resume after 4 cycles expire. If the main
external oscillator was used, the code execution will resume when 4096 cycles expire.
The customers need to reconfigure the PLL and clock dividers accordingly.
7.25.4.3
Power-down mode
Power-down mode does everything that Sleep mode does, but also turns off the IRC
oscillator and the flash memory. This saves more power, but requires waiting for
resumption of flash operation before execution of code or data access in the flash memory
can be accomplished.
On the wake-up from Power-down mode, if the IRC was used before entering
Power-down mode, it will take IRC 60
s to start-up. After this 4 IRC cycles will expire
before the code execution can then be resumed if the code was running from SRAM. In
相關PDF資料
PDF描述
LPC2468FET208 Single-chip 16-bit-32-bit micro; 512 kB flash, Ethernet, CAN, ISP-IAP, USB 2.0 device-host-OTG, external memory interface
LPC2470FBD208 Flashless 16-bit-32-bit microcontroller; Ethernet, CAN, LCD, USB 2.0 device-host-OTG, external memory interface
LPC2470FET208 Flashless 16-bit-32-bit microcontroller; Ethernet, CAN, LCD, USB 2.0 device-host-OTG, external memory interface
LPC2478FBD208 Single-chip 16-bit-32-bit micro; 512 kB flash, Ethernet, CAN, LCD, USB 2.0 device-host-OTG, external memory interface
LPC2478FET208 Single-chip 16-bit-32-bit micro; 512 kB flash, Ethernet, CAN, LCD, USB 2.0 device-host-OTG, external memory interface
相關代理商/技術參數
參數描述
LPC2468FBD208,551 功能描述:ARM微控制器 - MCU ARM7 512KF/USBH/ENET RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT
LPC2468FBD208551 制造商:NXP Semiconductors 功能描述:IC 32BIT MCU 72MHZ LQFP-208
LPC2468FET208 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Single-chip 16-bit/32-bit micro; 512 kB flash, Ethernet, CAN, ISP/IAP, USB 2.0 device/host/OTG, external memory interface
LPC2468FET208,551 功能描述:ARM微控制器 - MCU ARM7 512KF/USBH/ENET RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT
LPC2468FET208/CP3E 制造商:NXP Semiconductors 功能描述:- Trays
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*