參數資料
型號: LPC2361FBD100
廠商: NXP Semiconductors N.V.
元件分類: 數學處理器
英文描述: Single-chip 16-bit-32-bit MCU; up to 128 kB flash with ISP-IAP, Ethernet, USB 2.0 device-host-OTG, CAN, and 10-bit ADC-DAC
封裝: LPC2361FBD100<SOT407-1 (LQFP100)|<<http://www.nxp.com/packages/SOT407-1.html<1<Always Pb-free,;LPC2362FBD100<SOT407-1 (LQFP100)|<<http://www.nxp.com/packages/SOT407-1.htm
文件頁數: 52/64頁
文件大?。?/td> 475K
代理商: LPC2361FBD100
LPC2361_62
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 5 — 25 October 2011
52 of 64
NXP Semiconductors
LPC2361/62
Single-chip 16-bit/32-bit MCU
14.2 Crystal oscillator XTAL input and component selection
The input voltage to the on-chip oscillators is limited to 1.8 V. If the oscillator is driven by a
clock in slave mode, it is recommended that the input be coupled through a capacitor with
C
i
= 100 pF. To limit the input voltage to the specified range, choose an additional
capacitor to ground C
g
which attenuates the input voltage by a factor C
i
/ (C
i
+ C
g
). In
slave mode, a minimum of 200 mV (RMS) is needed.
In slave mode the input clock signal should be coupled by means of a capacitor of 100 pF
(
Figure 22
), with an amplitude between 200 mV (RMS) and 1000 mV (RMS). This
corresponds to a square wave signal with a signal swing of between 280 mV and 1.4 V.
The XTAL2 pin in this configuration can be left unconnected.
External components and models used in oscillation mode are shown in
Figure 23
and in
Table 15
and
Table 16
. Since the feedback resistance is integrated on chip, only a crystal
and the capacitances C
X1
and C
X2
need to be connected externally in case of
fundamental mode oscillation (the fundamental frequency is represented by L, C
L
and
R
S
). Capacitance C
P
in
Figure 23
represents the parallel package capacitance and should
not be larger than 7 pF. Parameters F
OSC
, C
L
, R
S
and C
P
are supplied by the crystal
manufacturer.
Fig 21. LPC2361/2362 USB device port configuration
LPC2361/62
USB-B
connector
33
Ω
33
Ω
002aad968
USB_UP_LED
USB_CONNECT
V
DD
V
DD
D+
D
USB_D+
USB_D
V
BUS
V
BUS
V
SS
Fig 22. Slave mode operation of the on-chip oscillator
LPC2xxx
XTAL1
Ci
100 pF
Cg
002aae718
相關PDF資料
PDF描述
LPC2362FBD100 Single-chip 16-bit-32-bit MCU; up to 128 kB flash with ISP-IAP, Ethernet, USB 2.0 device-host-OTG, CAN, and 10-bit ADC-DAC
LPC2364FBD100 ARM7 with 128 kB flash, 34 kB SRAM, Ethernet, USB 2.0 Device, CAN, and 10-bit ADC
LPC2365FBD100 ARM7 with 256 kB flash, 58 kB SRAM, Ethernet and 10-bit ADC
LPC2366FBD100 ARM7 with 256 kB flash, 58 kB SRAM, Ethernet, USB 2.0 Device, CAN, and 10-bit ADC
LPC2367FBD100 ARM7 with 512 kB flash, 58 kB SRAM, Ethernet and 10-bit ADC
相關代理商/技術參數
參數描述
LPC2361FBD100,551 功能描述:ARM微控制器 - MCU 64K FL/34K RAM USB OTG CAN RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT
LPC2362 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Single-chip 16-bit/32-bit MCU; up to 128 kB flash with ISP/IAP, Ethernet, USB 2.0 device/host/OTG, CAN, and 10-bit ADC/DAC
LPC2362FBD100 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Single-chip 16-bit/32-bit MCU; up to 128 kB flash with ISP/IAP, Ethernet, USB 2.0 device/host/OTG, CAN, and 10-bit ADC/DAC
LPC2362FBD100,551 功能描述:ARM微控制器 - MCU 128K FL/ ETH USB OTG CAN RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT
LPC2364 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Single-chip 16-bit/32-bit microcontrollers; up to 512 kB flash with ISP/IAP, Ethernet, USB 2.0, CAN, and 10-bit ADC/DAC