- 您現在的位置：買賣IC網 > PDF目錄369813 > LPC2103FA44 (NXP SEMICONDUCTORS) Single-chip 16-bit/32-bit microcontrollers; 8 kB/16 kB/32 kB flash with ISP/IAP, fast ports and 10-bit ADC PDF資料下載
參數資料
| 型號： | LPC2103FA44 |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | Single-chip 16-bit/32-bit microcontrollers; 8 kB/16 kB/32 kB flash with ISP/IAP, fast ports and 10-bit ADC |
| 中文描述： | 32-BIT, FLASH, 70 MHz, RISC MICROCONTROLLER, PQCC44 |
| 封裝： | PLASTIC, MS-018, SOT-187-2, LCC-44 |
| 文件頁數： | 12/32頁 |
| 文件大?。?/td> | 128K |
| 代理商： | LPC2103FA44 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
LPC2101_02_03_1
Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Preliminary data sheet
Rev. 01 — 18 January 2006
12 of 32
Philips Semiconductors
LPC2101/2102/2103
Single-chip 16-bit/32-bit microcontrollers
6.5 Interrupt controller
The VIC accepts all of the interrupt request inputs and categorizes them as FIQ, vectored
IRQ, and non-vectored IRQ as defined by programmable settings. The programmable
assignment scheme means that priorities of interrupts from the various peripherals can be
dynamically assigned and adjusted.
FIQ has the highest priority. If more than one request is assigned to FIQ, the VIC
combines the requests to produce the FIQ signal to the ARM processor. The fastest
possible FIQ latency is achieved when only one request is classified as FIQ, because then
the FIQ service routine does not need to branch into the interrupt service routine but can
run from the interrupt vector location. If more than one request is assigned to the FIQ
class, the FIQ service routine will read a word from the VIC that identifies which FIQ
source(s) is (are) requesting an interrupt.
Vectored IRQs have the middle priority. Sixteen of the interrupt requests can be assigned
to this category. Any of the interrupt requests can be assigned to any of the 16 vectored
IRQ slots, among which slot 0 has the highest priority and slot 15 has the lowest.
Non-vectored IRQs have the lowest priority.
The VIC combines the requests from all the vectored and non-vectored IRQs to produce
the IRQ signal to the ARM processor. The IRQ service routine can start by reading a
register from the VIC and jumping there. If any of the vectored IRQs are pending, the VIC
provides the address of the highest-priority requesting IRQs service routine, otherwise it
provides the address of a default routine that is shared by all the non-vectored IRQs. The
default routine can read another VIC register to see what IRQs are active.
6.5.1
Interrupt sources
Each peripheral device has one interrupt line connected to the Vectored Interrupt
Controller, but may have several internal interrupt flags. Individual interrupt flags may also
represent more than one interrupt source.
6.6 Pin connect block
The pin connect block allows selected pins of the microcontroller to have more than one
function. Configuration registers control the multiplexers to allow connection between the
pin and the on chip peripherals. Peripherals should be connected to the appropriate pins
prior to being activated, and prior to any related interrupt(s) being enabled. Activity of any
enabled peripheral function that is not mapped to a related pin should be considered
undefined.
The Pin Control Module with its pin select registers defines the functionality of the
microcontroller in a given hardware environment.
After reset all pins of Port 0 are configured as input with the following exceptions: If debug
is enabled, the JTAG pins will assume their JTAG functionality. The pins associated with
the I
2
C0 interface are open-drain.
相關PDF資料 |
PDF描述 |
|---|---|
| LPC2114 | Single-chip 16/32-bit microcontrollers; 128/256 kB ISP/IAP Flash with 10-bit ADC |
| LPC2124 | Single Chip 32-bit Microcontroller Erratasheet |
| LPC2131 | Single-chip 16/32-bit microcontrollers; 32/64/512 kB ISP/IAP Flash with 10-bit ADC and DAC |
| LPC2132 | Single-chip 16/32-bit microcontrollers; 32/64/512 kB ISP/IAP Flash with 10-bit ADC and DAC |
| LPC2142 | Single-chip 16-bit/32-bit microcontrollers; up to 512 kB flash with ISP/IAP, USB 2.0 full-speed device, 10-bit ADC and DAC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LPC2103FBD48 | 制造商:NXP Semiconductors 功能描述:IC SM 16/32-BIT ARM7 MCU WAFFLE125 制造商:NXP Semiconductors 功能描述:16/32BIT ARM7 MCU 16K FLASH SMD 制造商:NXP Semiconductors 功能描述:16/32BIT ARM7 MCU, 16K FLASH, SMD |
| LPC2103FBD48,118 | 功能描述:ARM微控制器 - MCU 32K FL/8K RAM/8CH RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT |
| LPC2103FBD48,151 | 功能描述:ARM微控制器 - MCU ARM7 32KF/8KR/10BADC RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT |
| LPC2103FBD48.151 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Single-chip 16-bit/32-bit microcontrollers; 8 kB/16 kB/32 kB flash with ISP/IAP, fast ports and 10-bit ADC |
| LPC2103FBD48151 | 制造商:NXP Semiconductors 功能描述:IC 32BIT MCU ARM7 70MHZ LQFP-48 |
發布緊急采購，3分鐘左右您將得到回復。