- 您現在的位置：買賣IC網 > PDF目錄383288 > LNBH21PD-TR (意法半導體) LNB SUPPLY AND CONTROL IC WITH STEP-UP CONVERTER AND I2C INTERFACE PDF資料下載
參數資料
| 型號： | LNBH21PD-TR |
| 廠商： | 意法半導體 |
| 英文描述： | LNB SUPPLY AND CONTROL IC WITH STEP-UP CONVERTER AND I2C INTERFACE |
| 中文描述： | LNB電源與控制集成電路升壓轉換器和I2C接口 |
| 文件頁數： | 9/20頁 |
| 文件大?。?/td> | 493K |
| 代理商： | LNBH21PD-TR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁
LNBH21
9/20
DiSEqCTM IMPLEMENTATION
The LNBH21 helps the system designer to implement the bi-directional (2.0) DiSEqC protocol by allowing
an easy PWK modulation/demodulation of the 22KHz carrier. The PWK data are exchanged between the
LNBH21 and the main μP using logic levels that are compatible with both 3.3 and 5V microcontrollers.
This data exchange is made through two dedicated pins, DSQIN and DSQOUT, in order to maintain the
timing relationships between the PWK data and the PWK modulation as accurate as possible. These two
pins should be directly connected to two I/O pins of the μP, thus leaving to the resident firmware the task
of encoding and decoding the PWK data in accordance to the DiSEqC protocol. Full compliance of the
system to the specification is thus not implied by the bare use of the LNBH21. The system designer should
also take in consideration the bus hardware requirements; that can be simply accomplished by the R-L
termination connected on the V
O
pins of the LNBH21, as shown in the Typical Application Circuit on page
4. To avoid any losses due to the R-L impedance during the tone transmission, the LNBH21 has
dedicated output (V
O
TX) that, in a DiSEqC 2.0 application, is connected after the filter and must be
enabled by setting the TTX SR bit HIGH only during the tone transmission (see DiSEqC 2.O operation
description on page 2).
Unidirectional (1.x) DiSEqC and non-DiSEqC systems normally don't need this termination, and the V
O
TX
pin can be directly connected to the LNB supply port of the Tuner (see DiSeqC 1.x application circuit on
pag.4). There is also no need of Tone Decoding, thus DETIN and DSQOUT pins can be left unconnected
and the Tone is provided by the V
O
TX.
相關PDF資料 |
PDF描述 |
|---|---|
| LNBK15SP | LNB SUPPLY AND CONTROL VOLTAGE REGULATOR PARALLEL INTERFACE |
| LNBK16 | LNB SUPPLY AND CONTROL VOLTAGE REGULATOR PARALLEL INTERFACE |
| LNBK16SP | LNB SUPPLY AND CONTROL VOLTAGE REGULATOR PARALLEL INTERFACE |
| LNBK20 | LNB SUPPLY AND CONTROL VOLTAGE REGULATOR PARALLEL INTERFACE |
| LNBK20CR | LNB SUPPLY AND CONTROL VOLTAGE REGULATOR PARALLEL INTERFACE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LNBH21PPR | 制造商:STMicroelectronics 功能描述:LNBH21PPR - Tape and Reel |
| LNBH221 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:DUAL LNB SUPPLY AND CONTROL IC WITH STEP-UP CONVERTER AND I2C INTERFACE |
| LNBH221/1TM | 制造商:STMicroelectronics 功能描述:LNB SUPPLY/CONTROL REGULATOR, 36 Pin, Plastic, SSOP |
| LNBH221/1TM-TR | 制造商:STMicroelectronics 功能描述:LNB SUPPLY/CONTROL REGULATOR, 36 Pin, Plastic, SSOP |
| LNBH221_06 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Dual LNB supply and control IC with Step-Up converter and I2C interface |
發布緊急采購，3分鐘左右您將得到回復。