- 您現在的位置：買賣IC網 > PDF目錄358877 > LM95010CIMM (NATIONAL SEMICONDUCTOR CORP) Digital Temperature Sensor with SensorPath⑩ Bus in MSOP8 Package PDF資料下載
參數資料
| 型號： | LM95010CIMM |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 溫度/濕度傳感器 |
| 英文描述： | Digital Temperature Sensor with SensorPath⑩ Bus in MSOP8 Package |
| 中文描述： | DIGITAL TEMP SENSOR-SERIAL, 10BIT(s), 2Cel, SQUARE, SURFACE MOUNT |
| 封裝： | MO-187, MSOP-8 |
| 文件頁數： | 18/19頁 |
| 文件大?。?/td> | 275K |
| 代理商： | LM95010CIMM |
3.0 Applications Information
3.1 MOUNTING CONSIDERATIONS
The LM95010 can be applied easily in the same way as
other integrated-circuit temperature sensors. It can be glued
or cemented to a surface. The temperature that the
LM95010 is reading will typically be within +0.2 C of the
surface temperature to which the LM95010’s leads are at-
tached to.
This presumes that the ambient air temperature is almost the
same as the surface temperature; if the air temperature were
much higher or lower than the surface temperature, the
actual temperature measured would be at an intermediate
temperature between the surface temperature and the air
temperature.
Alternatively, the LM95010 can be mounted inside a sealed-
end metal tube, and can then be dipped into a bath or
screwed into a threaded hole in a tank. As with any IC, the
LM95010 and accompanying wiring and circuits must be
kept insulated and dry, to avoid leakage and corrosion. This
is especially true if the circuit may operate at cold tempera-
tures where condensation can occur. Printed-circuit coatings
and varnishes such as Humiseal and epoxy paints or dips
are often used to ensure that moisture cannot corrode the
LM95010 or its connections.
The thermal resistance junction to ambient (
θ
JA
) is the pa-
rameter used to calculate the rise of a device junction tem-
perature due to its power dissipation. For the LM95010 the
equation used to calculate the rise in the die temperature is
as follows: T
J
= T
A
+
θ
JA
x [(V
+
x I
Q
) + (V
OL
x I
OL
)]
where I
Q
is the quiescent current (500 μA typ.), V
OL
is the
logic "Low" output level of SWD, and I
OL
is the load current
on SWD. Since the LM95010’s junction temperature is the
actual temperature being measured care should be taken to
minimize the load current that the LM95010 is require to
drive. When mounted to a PCB, with 2 oz. copper foil, the
LM95010’s thermal resistance is typically 210 C/W.
L
www.national.com
18
相關PDF資料 |
PDF描述 |
|---|---|
| LM95071 | SPI/MICROWIRE⑩ 13-Bit Plus Sign Temperature Sensor |
| LM95071CIMFX | SPI/MICROWIRE⑩ 13-Bit Plus Sign Temperature Sensor |
| LM96000 | Hardware Monitor with Integrated Fan Control |
| LM96000CIMT | Hardware Monitor with Integrated Fan Control |
| LM96000CIMTX | Hardware Monitor with Integrated Fan Control |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM95010CIMM/NOPB | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| LM95010CIMMX | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| LM95010CIMMX/NOPB | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| LM95010EVAL | 功能描述:溫度傳感器開發工具 LM95010 EVAL BOARD RoHS:否 制造商:Texas Instruments 產品類型:Temperature Sensors and Control ICs 工具用于評估:MSP430G2553 接口類型:USB 工作電源電壓: 工作電源電流: |
| LM95071 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:SPI/MICROWIRE⑩ 13-Bit Plus Sign Temperature Sensor |
發布緊急采購，3分鐘左右您將得到回復。