參數資料
型號： LM87
廠商： National Semiconductor Corporation
英文描述： Serial Interface System Hardware Monitor with Remote Diode Temperature Sensing
中文描述： 串行接口系統硬件監控與遠程二極管溫度傳感器
文件頁數： 18/32頁
文件大?。?/td> 470K
代理商： LM87
Functional Description
(Continued)
η
from part to part. As an example, assume a temperature
sensor has an accuracy specification of
±
3C at room tem-
perature of 25C and the process used to manufacture the
diode has a non-ideality variation of
±
1%. The resulting
accuracy of the temperature sensor at room temperature will
be:
T
ACC
=
±
3C + (
±
1% of 298K) =
±
6C
.
The additional inaccuracy in the temperature measurement
caused by
η
, can be eliminated if each temperature sensor is
calibrated with the remote diode that it will be paired with.
8.5 PCB Layout Recommendations for Minimizing
Noise
In a noisy environment, such as a processor mother board,
layout considerations are very critical. Noise induced on
traces running between the remote temperature diode sen-
sor and the LM87 can cause temperature conversion errors.
The following guidelines should be followed:
1.
Place a 0.1 μF power supply bypass capacitor as close
as possible to the V
pin and the recommended 2.2 nF
capacitor as close as possible to the D+ and D pins.
Make sure the traces to the 2.2 nF capacitor are
matched.
Ideally, the LM87 should be placed within 10 cm of the
Processor diode pins with the traces being as straight,
short and identical as possible.
Diode traces should be surrounded by a GND guard ring
to either side, above and below if possible. This GND
guard should not be between the D+ and D lines. In the
event that noise does couple to the diode lines it would
be ideal if it is coupled common mode. That is equally to
the D+ and D lines.
Avoid routing diode traces in close proximity to power
supply switching or filtering inductors.
Avoid running diode traces close to or parallel to high
speed digital and bus lines. Diode traces should be kept
at least 2 cm. apart from the high speed digital traces.
If it is necessary to cross high speed digital traces, the
diode traces and the high speed digital traces should
cross at a 90 degree angle.
The ideal place to connect the LM87’s GND pin is as
close as possible to the Processors GND associated
with the sense diode. For the Pentium II this would be
pin A14.
2.
3.
4.
5.
6.
7.
Noise on the digital lines, overshoot greater than V
and
undershoot less than GND, may prevent successful SMBus
communication with the LM87. SMBus no acknowledge is
the most common symptom, causing unnecessary traffic on
the bus. Although, the SMBus maximum frequency of com-
munication is rather low (400 kHz max) care still needs to be
taken to ensure proper termination within a system with
multiple parts on the bus and long printed circuit board
traces. A lowpass filter, in series with the SMBCLK and
SMBData, has been added internally to the LM87 for noise
immunity. The lowpass filter has a typical cutoff frequency of
20MHz. Additional noise immunity can be achieved by plac-
ing a resistor (4.7k to 5.1k Ohms) in series with the SMBCLK
input as close to the LM87 as possible. This resistance, in
conjunction with the IC input capacitance, reduces high fre-
quency noise seen at the SMBCLK input and increases the
reliability of communications.
10099535
FIGURE 9. Recommended Diode Trace Layout
L
www.national.com
18
相關PDF資料
PDF描述
LM89 【0.75∑C Accurate, Remote Diode and Local Digital Temperature Sensor with Two-Wire Interface
LM8M64 Color STN LCD Module
LM8V302 Color STN-LCD Module(Handheld PC)
LM8V30 Color STN-LCD Module(Handheld PC)
LM8V311 DEVlCESPECIFICATIONfoor for Passive Matrix Color LCD Module (640 X 480 dots)
相關代理商/技術參數
參數描述
LM87CIMT 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
LM87CIMT 制造商:Texas Instruments 功能描述:HDW MON, 2 REMOTE TEMP SENS, SMD 制造商:Texas Instruments 功能描述:HDW MON, 2 REMOTE TEMP SENS, SMD; IC Output Type:Voltage; Sensing Accuracy Range: 3C; Sensing Temperature Min:-40C; Sensing Temperature Max:+125C; Supply Voltage Min:2.8V; Supply Voltage Max:3.8V; Sensor Case Style:TSSOP; No. of ;RoHS Compliant: Yes
LM87CIMT/NOPB 功能描述:板上安裝溫度傳感器 Hdw Mon & 2 Remote Temp Sens RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
LM87CIMTX 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
LM87CIMTX/NOPB 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*