- 您現在的位置：買賣IC網 > PDF目錄358877 > LM87 (National Semiconductor Corporation) Serial Interface System Hardware Monitor with Remote Diode Temperature Sensing PDF資料下載
參數資料
| 型號： | LM87 |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | Serial Interface System Hardware Monitor with Remote Diode Temperature Sensing |
| 中文描述： | 串行接口系統硬件監控與遠程二極管溫度傳感器 |
| 文件頁數： | 13/32頁 |
| 文件大?。?/td> | 470K |
| 代理商： | LM87 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
Functional Description
(Continued)
power up. If ADD is tied to ground the value for XY is 10. If
ADD is tied to Vcc XY will be set to 01. If ADD is not
connected, XY will be 00. XY = 11 is not a possible combi-
nation.
All of these communications are depicted in the Serial Bus
Interface Timing Diagrams as shown in
Figure 5
. The ex-
ample shown corresponds to the ADD pin tied to Vcc, so
XY=01 and the resulting LM87 address is 0101101.
Serial Bus Timeout can be initiated by holding the SMBCLK
line low for greater than t
(35 ms max). Serial Bus
Timeout resets the serial bus interface circuitry to the idle
state and readies the LM87 for a new serial bus communi-
cation.
3.0 USING THE LM87
3.1 Power On
When power is first applied, the LM87 performs a “power on
reset” on several of its registers. The power on condition of
the LM87’s registers is shown in
Table 1. The internal regis-
ters and their corresponding internal LM87 addresses are as
follows:
Registers whose power on values are not shown
have power on conditions that are indeterminate (this in-
cludes the value RAM ,exclusive of the DAC data, and
WATCHDOG limits). When power is first applied the ADC is
inactive. In most applications, the first action after power on
is to write WATCHDOG limits into the Value RAM.
3.2 Resets
All register values, except the Programmed DAC Output can
be returned to their "power on" default values by taking the
RESET
#
input low for at least TBD ns or by performing a
Configuration Register INITIALIZATION. The Value RAM
conversion results, and Value RAM WATCHDOG limits are
not Reset and will be indeterminate immediately after power
on. If the Value RAM contains valid conversion results and/or
Value RAM WATCHDOG limits have been previously set,
they will not be affected by a Configuration Register INITIAL-
IZATION. The Power On Reset, RESET# input, and Configu-
ration Register INITIALIZATION, clear or initialize the follow-
ing registers (the initialized values are shown on Table I).
Power On Reset also sets the Programmed DAC Output to
full scale (FFh) Hardware High Limit registers 13h, and 14h
will only be returned to default values if the "Write Once" bits
in Configuration Register 2 have not been set:
Configuration Registers 1 and 2
Channel Mode Register
Hardware High Limit Registers
Interrupt Status Register 1
Interrupt Status Register 2
Interrupt Status Mirror Register 1
Interrupt Status Mirror Register 2
Interrupt Mask Register 1
Interrupt Mask Register 2
Chassis Intrusion Clear Register
VID/Fan Divisor Register
VID4 Register
Extended Mode Register
Configuration Register INITIALIZATION is accomplished by
setting Bit 7 of Configuration Register 1 high. This bit auto-
matically clears after being set.
3.3 Configuration Registers and Channel Mode
Register
The Configuration Registers and Channel Mode Register
control the LM87 operation.At power on, theADC is stopped
and INT_Clear is asserted, clearing the INT
#
hardwire out-
put. These registers start and stop the LM87, enable and
disable interrupt output, configure the operation of dual func-
tion inputs, and provide the Reset functions described in
Section 3.2
.
Bit 0 of Configuration Register 1 controls the monitoring loop
of the LM87. Setting Bit 0 low stops the LM87 monitoring
loop and puts the LM87 in shutdown mode, reducing power
consumption. Serial Bus communication can take place with
any register in the LM87 although activity on the SMBData
and SMBCLK lines will increase shutdown current, up to as
much as maximum rated supply current, while the activity
takes place. Taking Bit 0 high starts the monitoring loop,
described in more detail subsequently.
Bit 1 of Configuration Register 1 enables the INT
#
Interrupt
output when this bit is taken high.
Bit 2 of Configuration Register 1 enables the THERM
#
Inter-
rupt output when this bit is taken high.
Bit 3 of Configuration Register 1 clears the INT# output when
set high, without affecting the contents of the Interrupt Status
Registers. The LM87 will stop monitoring. It will resume upon
clearing of this bit.
Bit 4 of Configuration Register 1 provides an active low 20
ms (minimum) pulse at the RESET
#
output when set high.
Bit 6 of Configuration Register 1 clears the THERM# output
when set high, without affecting the contents of the Interrupt
Status Registers.
Bit 7 of Configuration Register 1 (the INITIALIZATION bit)
resets the internal registers of the LM87 as described in
Section 3.2
.
Bit 7 of the CI_Clear Register provides an active low 20 ms
(minimum) pulse at the CI
#
output pin when set high. This is
intended for resetting the Chassis Intrusion circuitry.
Bit 0 of Configuration Register 2 enables the INT
#
Interrupt
output for THERM# events when set low. When this bit is set
high, THERM# error events will not affect the INT# output.
Bit 1 of Configuration Register 2 locks the value set in the
Internal Temperature high limit register at 13h. The value
cannot be changed until a Power On Reset is performed.
Bit 2 of Configuration Register 2 locks the value set in the
External Temperature high limit register at 14h. The value
cannot be changed until a Power On Reset is performed.
Bit 3 of Configuration Register 2 sets the THERM# output
mode. When set to 0, the THERM# output functions in
default mode, when set to 1, THERM# operates in ACPI
mode.
Bit 6 of Configuration Register 2, when set to 1, enables pin
21 as an active high (IRQ3) interrupt input. When set to 0,
this input is disabled as an IRQ interrupt.
Bit 7 of Configuration Register 2, when set to 1, enables pin
20 as an active high (IRQ4) interrupt input. When set to 0,
this input is disabled as an IRQ interrupt.
Bit 0 of the Channel Mode Register, when set to 1, config-
ures pin 5 as AIN1. When set to 0, pin 5 is configured as the
FAN1 input.
Bit 1 of the Channel Mode Register, when set to 1, config-
ures pin 6 as AIN2. When set to 0, pin 6 is configured as the
FAN2 input.
L
www.national.com
13
相關PDF資料 |
PDF描述 |
|---|---|
| LM89 | 【0.75∑C Accurate, Remote Diode and Local Digital Temperature Sensor with Two-Wire Interface |
| LM8M64 | Color STN LCD Module |
| LM8V302 | Color STN-LCD Module(Handheld PC) |
| LM8V30 | Color STN-LCD Module(Handheld PC) |
| LM8V311 | DEVlCESPECIFICATIONfoor for Passive Matrix Color LCD Module (640 X 480 dots) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM87CIMT | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| LM87CIMT | 制造商:Texas Instruments 功能描述:HDW MON, 2 REMOTE TEMP SENS, SMD 制造商:Texas Instruments 功能描述:HDW MON, 2 REMOTE TEMP SENS, SMD; IC Output Type:Voltage; Sensing Accuracy Range: 3C; Sensing Temperature Min:-40C; Sensing Temperature Max:+125C; Supply Voltage Min:2.8V; Supply Voltage Max:3.8V; Sensor Case Style:TSSOP; No. of ;RoHS Compliant: Yes |
| LM87CIMT/NOPB | 功能描述:板上安裝溫度傳感器 Hdw Mon & 2 Remote Temp Sens RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| LM87CIMTX | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| LM87CIMTX/NOPB | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
發布緊急采購，3分鐘左右您將得到回復。