- 您現(xiàn)在的位置：買賣IC網 > PDF目錄358877 > LM83CIMQAX (National Semiconductor Corporation) Triple-Diode Input and Local Digital Temperature Sensor with Two-Wire Interface PDF資料下載
參數資料
| 型號： | LM83CIMQAX |
| 廠商： | National Semiconductor Corporation |
| 元件分類： | 溫度/濕度傳感器 |
| 英文描述： | Triple-Diode Input and Local Digital Temperature Sensor with Two-Wire Interface |
| 中文描述： | 三二極管輸入和本地數字溫度傳感器兩線接口 |
| 文件頁數： | 9/20頁 |
| 文件大?。?/td> | 331K |
| 代理商： | LM83CIMQAX |
1.0 Functional Description
(Continued)
Register flags are updated at the completion of a conversion,
which occurs approximately 60 ms after a temperature diode
is sampled. INT is deactivated when the Status Register,
containing the set bit, is read and a temperature reading is
less than or equal to it’s corresponding HIGH setpoint, as
shown in Figure 4 Figure 5shows a simplified logic diagram
for the INT output and related circuitry.
The INT output can be disabled by setting the INT mask bit,
D7, of the configuration register. INT can be programmed to
be active high or low by the state of the INT inversion bit, D1,
in the configuration register. A “0” would program INT to be
active low. INT is an open-drain output.
1.3 T_CRIT_A OUTPUT and T_CRIT LIMIT
T_CRIT_A is activated when any temperature reading is
greater than the limit preset in the critical temperature set-
point register (T_CRIT), as shown in Figure 6 The Status
Registers can be read to determine which event caused the
alarm. A bit in the Status Registers is set high to indicate
which temperature reading exceeded the T_CRIT setpoint
temperature and caused the alarm, see Section 2.3
Local and remote temperature diodes are sampled in se-
quence by the A/D converter. The T_CRIT_A output and the
Status Register flags are updated at the completion of a con-
version. T_CRIT_A and the Status Register flags are reset
only after the Status Register is read and if a temperature
conversion is below the T_CRIT setpoint, as shown in Figure
6 Figure 7 shows a simplified logic diagram of the
T_CRIT_A and related circuitry.
Located in the Configuration Register are the mask bits for
each temperature reading, seeSection 2.5 When a mask bit
is set, its corresponding status flag will not propagate to the
T_CRIT_A output, but will still be set in the Status Registers.
Setting all four mask bits or programming the T_CRIT set-
point to 127C will disable the T_CRIT_A output.
1.4 POWER ON RESET DEFAULT STATES
LM83 always powers up to these known default states:
1.
Command Register set to 00h
2.
Local Temperature set to 0C
DS101058-14
b Note: Status Register Bits are reset by a read of Status Register where
FIGURE 4. INT Temperature Response Diagram with
D2RHS and D3RHS set to 127C.
DS101058-21
FIGURE 5. INT output related circuitry logic diagram
DS101058-6
b Note: Status Register Bits are reset by a read of Status Register where
FIGURE 6. T_CRIT_A Temperature Response Diagram
with remote diode 1 and local temperature masked.
DS101058-20
FIGURE 7. T_CRIT_A output related circuitry logic
diagram
L
www.national.com
9
相關PDF資料 |
PDF描述 |
|---|---|
| LM8560B | Digital Alarm Clock(用于驅動LED顯示設備的數字鬧鐘) |
| LM8562 | Digital Alarm Clock(用于驅動LED顯示設備的數字鬧鐘) |
| LM8569 | Digital Alarm Clock(數字鬧鐘) |
| LM87 | Serial Interface System Hardware Monitor with Remote Diode Temperature Sensing |
| LM89 | 【0.75∑C Accurate, Remote Diode and Local Digital Temperature Sensor with Two-Wire Interface |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM83CIMQAX/NOPB | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| LM84 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Diode Input Digital Temperature Sensor with Two-Wire Interface |
| LM8400 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Four Wire Resistive Touchscreen Controller with Brownout |
| LM8460 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:ALARM CLOCK (CLOCK RADIO.ETC) |
| LM8471 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
發(fā)布緊急采購，3分鐘左右您將得到回復。