- 您現在的位置：買賣IC網 > PDF目錄361034 > LM82 (National Semiconductor Corporation) Remote Diode and Local Digital Temperature Sensor with Two-Wire Interface PDF資料下載
參數資料
| 型號： | LM82 |
| 廠商： | National Semiconductor Corporation |
| 元件分類： | 溫度/濕度傳感器 |
| 英文描述： | Remote Diode and Local Digital Temperature Sensor with Two-Wire Interface |
| 中文描述： | 遠程二極管和本地?cái)?shù)字溫度傳感器兩線接口 |
| 文件頁數： | 9/17頁 |
| 文件大?。?/td> | 341K |
| 代理商： | LM82 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁
1.0 Functional Description
(Continued)
less than or equal to it’s corresponding HIGH setpoint, as
shown in Figure 4 Figure 5shows a simplified logic diagram
for the INT output and related circuitry.
The INT output can be disabled by setting the INT mask bit,
D7, of the configuration register. INT can be programmed to
be active high or low by the state of the INT inversion bit, D1,
in the configuration register. A “0” would program INT to be
active low. INT is an open-drain output.
1.3 T_CRIT_A OUTPUT and T_CRIT LIMIT
T_CRIT_A is activated when any temperature reading is
greater than the limit preset in the critical temperature set-
point register (T_CRIT), as shown in Figure 6 The Status
Registers can be read to determine which event caused the
alarm. A bit in the Status Registers is set high to indicate
which temperature reading exceeded the T_CRIT setpoint
temperature and caused the alarm, see Section 2.3
Local and remote temperature diodes are sampled in se-
quence by the A/D converter. The T_CRIT_A output and the
Status Register flags are updated at the completion of a con-
version. T_CRIT_A and the Status Register flags are reset
only after the Status Register is read and if a temperature
conversion is below the T_CRIT setpoint, as shown in Figure
6 Figure 7 shows a simplified logic diagram of the
T_CRIT_A and related circuitry.
Located in the Configuration Register are the mask bits for
each temperature reading, seeSection 2.5 When a mask bit
is set, its corresponding status flag will not propagate to the
T_CRIT_A output, but will still be set in the Status Registers.
Configuration register bits D5 and D3, labled “Remote
T_CRIT_A mask” must be set high before the T_CRIT set-
point is lowered in order for the T_CRIT_A output to function
properly. Setting all four mask bits or programming the
T_CRIT setpoint to 127C will disable the T_CRIT_A output.
1.4 POWER ON RESET DEFAULT STATES
LM82 always powers up to these known default states:
1.
Command Register set to 00h
2.
Local Temperature set to 0C
3.
Remote Temperature set to 0C until the LM82 senses a
diode present between the D+ and D input pins.
4.
Status Register set to 00h.
5.
Configuration Register set to 00h; INT enabled and all
T_CRIT setpoints enabled to activate T_CRIT_A.
DS101297-14
*
Note: Status Register Bits are reset by a read of Status Register where
bit is located.
FIGURE 4. INT Temperature Response Diagram
DS101297-21
FIGURE 5. INT output related circuitry logic diagram
DS101297-6
*
Note: Status Register Bits are reset by a read of Status Register where
bit is located.
FIGURE 6. T_CRIT_A Temperature Response Diagram
DS101297-20
FIGURE 7. T_CRIT_A output related circuitry logic
diagram
L
www.national.com
9
相關PDF資料 |
PDF描述 |
|---|---|
| LM8300HVA9 | Four Wire Resistive Touchscreen Controller with Brownout |
| LM8300ILQ9 | Four Wire Resistive Touchscreen Controller with Brownout |
| LM8300IMT9 | Four Wire Resistive Touchscreen Controller with Brownout |
| LM8300IVA9 | Four Wire Resistive Touchscreen Controller with Brownout |
| LM8300 | Four Wire Resistive Touchscreen Controller with Brownout |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM82_04 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Remote Diode and Local Digital Temperature Sensor with Two-Wire Interface |
| LM8204 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:電話機集成電路互換表 |
| LM8207 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:TFT 18 Gamma Buffer + VCOM Driver + Voltage Reference |
| LM8207MT | 功能描述:LCD 驅動器 RoHS:否 制造商:Maxim Integrated 數位數量:4.5 片段數量:30 最大時鐘頻率:19 KHz 工作電源電壓:3 V to 3.6 V 最大工作溫度:+ 85 C 最小工作溫度:- 20 C 封裝 / 箱體:PDIP-40 封裝:Tube |
| LM8207MT/NOPB | 功能描述:LCD Gamma緩沖器 RoHS:否 制造商:Maxim Integrated 輸入補償電壓: 轉換速度: 電源電壓-最大:20 V 電源電壓-最小:9 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-38 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。