- 您現在的位置：買賣IC網 > PDF目錄361034 > LM82 (National Semiconductor Corporation) Remote Diode and Local Digital Temperature Sensor with Two-Wire Interface PDF資料下載
參數資料
| 型號： | LM82 |
| 廠商： | National Semiconductor Corporation |
| 元件分類： | 溫度/濕度傳感器 |
| 英文描述： | Remote Diode and Local Digital Temperature Sensor with Two-Wire Interface |
| 中文描述： | 遠程二極管和本地數字溫度傳感器兩線接口 |
| 文件頁數： | 11/17頁 |
| 文件大?。?/td> | 341K |
| 代理商： | LM82 |
1.0 Functional Description
(Continued)
1.9 COMMUNICATING with the LM82
There are 13 data registers in the LM82, selected by the
Command Register. At power-up the Command Register is
set to “00”, the location for the Read Local Temperature Reg-
ister. The Command Register latches the last location it was
set to. Reading the Status Register resets T_CRIT_A and
INT, so long as a temperature comparison does not signal a
fault (see Sections 1.2 and 1.3). All other registers are pre-
defined as read only or write only. Read and write registers
with the same function contain mirrored data.
A
Write
to the LM82 will always include the address byte and
the command byte. A write to any register requires one data
byte.
Reading
the LM82 can take place either of two ways:
1.
If the location latched in the Command Register is cor-
rect (most of the time it is expected that the Command
Register will point to one of the Read Temperature Reg-
isters because that will be the data most frequently read
from the LM82), then the read can simply consist of an
address byte, followed by retrieving the data byte.
2.
If the Command Register needs to be set, then an ad-
dress byte, command byte, repeat start, and another ad-
dress byte will accomplish a read.
The data byte has the most significant bit first. At the end of
a read, the LM82 can accept either Acknowledge or No Ac-
knowledge from the Master (No Acknowledge is typically
used as a signal for the slave that the Master has read its
last byte).
1.10 SERIAL INTERFACE ERROR RECOVERY
The LM82 SMBus lines will be reset to the SMBus idle state
if the SMBData or SMBCLK lines are held low for 40 ms or
more (t
TIMEOUT
). The LM82 may or may not reset the state of
the serial interface logic if either of the SMBData or SMBCLK
lines are held low between 25 ms and 40 ms. TIMEOUT al-
lows a clean recovery in cases where the master may be re-
set while the LM82 is transmitting a low bit thus preventing
possible bus lock up.
Whenever the LM82 sees the start condition its serial inter-
face will reset to the beginning of the communication, thus
the LM82 will expect to see an address byte next. This sim-
plifies recovery when the master is reset while the LM82 is
transmitting a high.
DS101297-9
L
www.national.com
11
相關PDF資料 |
PDF描述 |
|---|---|
| LM8300HVA9 | Four Wire Resistive Touchscreen Controller with Brownout |
| LM8300ILQ9 | Four Wire Resistive Touchscreen Controller with Brownout |
| LM8300IMT9 | Four Wire Resistive Touchscreen Controller with Brownout |
| LM8300IVA9 | Four Wire Resistive Touchscreen Controller with Brownout |
| LM8300 | Four Wire Resistive Touchscreen Controller with Brownout |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM82_04 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Remote Diode and Local Digital Temperature Sensor with Two-Wire Interface |
| LM8204 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:電話機集成電路互換表 |
| LM8207 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:TFT 18 Gamma Buffer + VCOM Driver + Voltage Reference |
| LM8207MT | 功能描述:LCD 驅動器 RoHS:否 制造商:Maxim Integrated 數位數量:4.5 片段數量:30 最大時鐘頻率:19 KHz 工作電源電壓:3 V to 3.6 V 最大工作溫度:+ 85 C 最小工作溫度:- 20 C 封裝 / 箱體:PDIP-40 封裝:Tube |
| LM8207MT/NOPB | 功能描述:LCD Gamma緩沖器 RoHS:否 制造商:Maxim Integrated 輸入補償電壓: 轉換速度: 電源電壓-最大:20 V 電源電壓-最小:9 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-38 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。