- 您現在的位置：買賣IC網 > PDF目錄369796 > LM81BIMT-3 DATA ACQ SYSTEM|6-CHANNEL|8-BIT|TSSOP|24PIN|PLASTIC PDF資料下載
參數資料
| 型號： | LM81BIMT-3 |
| 英文描述： | DATA ACQ SYSTEM|6-CHANNEL|8-BIT|TSSOP|24PIN|PLASTIC |
| 中文描述： | 數據ACQ木材系統| 6聲道| 8位| TSSOP封裝| 24針|塑料 |
| 文件頁數： | 23/33頁 |
| 文件大?。?/td> | 388K |
| 代理商： | LM81BIMT-3 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁
Functional Description
(Continued)
masks for each Interrupt. As described in Section 3.3, the
hardware Interrupt line can also be enabled/disabled in the
Configuration Register.
T_CRIT_A interrupt is dedicated to temperature and is indi-
cated in Extended Mode Register 1. Extended Mode Regis-
ter 1 controls T_CRIT_A.
9.1 Interrupt Clearing
Reading a Status Register will output the contents of the
Register, and reset the Register. A subsequent read done
before the analog “round-robin” monitoring loop is complete
will indicate a cleared Register.Allow at least 820 ms to allow
all Registers to be updated between reads. In summary, the
Interrupt Status Register clears upon being read, and re-
quires at least 400 ms to be updated. When the Interrupt
Status Register clears, the hardware interrupt line will also
clear until the Registers are updated by the monitoring loop.
The hardware Interrupt line (INT) is cleared with the
INT_Clear bit, which is Bit 3 of the Configuration Register.
When this bit is high, the LM81 monitoring loop will stop. It
will resume when the bit is low.
10.0 RESET I/O
RESET is intended to provide a master reset to devices
connected to this line. INT Mask Register 2, Bit 7, must be
set high to enable this function. Setting Bit 4 in the Configu-
ration Register high outputs a least 20 ms low on this line, at
the end of which Bit 4 in the Configuration Register automati-
cally clears. Again, the label for this pin is only its suggested
use. In applications where the RESET capability is not
needed it can be used for any type of digital control that
requires a 20 ms active low open-drain output.
RESET operates as an input when not activated by the
Configuration Register. Setting this line low will reset all of
the registers in the LM81 to their power on default state. All
Value RAM locations will not be affected except for the DAC
Data Register.
11.0 NAND TREE TESTS
A NAND tree is provided in the LM81 for Automated Test
Equipment (ATE) board level connectivity testing. DACOut/
NTEST_IN, T_CRIT_A, V
+
and GND pins are excluded from
NAND tree testing. Taking DACOut/NTEST_IN high before
the first write to the configuration register activates the
NAND Tree test mode. After the first write to the configura-
tion register the NAND Tree test mode cannot be reacti-
vated. To perform a NAND tree test all pins included in the
NAND tree should be driven to 1 forcing the A0/
NTEST_OUT high. Each individual pin starting with A1 and
concluding with SMBData (excluding DACOut/NTEST_IN,
T_CRIT_A, V
+
and GND) can be taken low with the resulting
toggle observed on the A0/NTEST_OUT pin. Allow for a
typical propagation delay of 500 ns.
DS100072-29
L
www.national.com
23
相關PDF資料 |
PDF描述 |
|---|---|
| LM81BIMTX-3 | DATA ACQ SYSTEM|6-CHANNEL|8-BIT|TSSOP|24PIN|PLASTIC |
| LM81CIMTX-3 | Single-Ended Data Acquisition System |
| LM8362_SERIES | |
| LM8363_SERIES | |
| LM8368_SERIES | |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM81BIMT-3/NOPB | 功能描述:監控電路 Improved Syst HW Mon RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| LM81BIMT-3/NOPB | 制造商:Texas Instruments 功能描述:, Resolution (Bits):8, Data Interface:Se |
| LM81BIMTX-3 | 功能描述:監控電路 RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| LM81BIMTX-3/NOPB | 功能描述:監控電路 RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| LM81C1MTX-3 | 制造商:Texas Instruments 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。