- 您現在的位置：買賣IC網 > PDF目錄369796 > LM81BIMT-3 DATA ACQ SYSTEM|6-CHANNEL|8-BIT|TSSOP|24PIN|PLASTIC PDF資料下載
參數資料
| 型號： | LM81BIMT-3 |
| 英文描述： | DATA ACQ SYSTEM|6-CHANNEL|8-BIT|TSSOP|24PIN|PLASTIC |
| 中文描述： | 數據ACQ木材系統| 6聲道| 8位| TSSOP封裝| 24針|塑料 |
| 文件頁數： | 20/33頁 |
| 文件大小： | 388K |
| 代理商： | LM81BIMT-3 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁
Functional Description
(Continued)
8.2 Temperature Interrupts
INT and T_CRIT_A outputs are provided for temperature
interrupt. Temperature interrupts have a normal and an ex-
tended option of operation. Each option has three different
modes of operation: Repetitive Interrupt, One-Time Interrupt
and Comparator.
Normal Repetitive Interrupt Mode
is shown in Figure 11
and operates in the following way: T_CRIT_A is disabled.
Exceeding T
causes an interrupt that will remain active
indefinitely until reset by reading Interrupt Status Register 1.
Once reset if the temperature remains above the T
setpoint the interrupt will again be activated at the comple-
tion of another conversion cycle. If temperature is less than
or equal to T
HIHYST
the interrupt will not be activated.
Normal One-Time Interrupt Mode
is shown in Figure 12
and operates in the following way: T_CRIT_A is disabled.
Exceeding T
HIGH
causes an interrupt that will remain active
indefinitely until reset by reading Interrupt Status Register 1.
Another interrupt will not occur until the temperature drops to
less than or equal to T
HIHYST
and then exceeds T
HIGH
during
a subsequent conversion. After power up this mode is se-
lected as default.
Normal Comparator Mode
is shown in Figure 13 and op-
erates in the following way: T_CRIT_A is disabled. Exceed-
ing T
HIGH
causes an interrupt that will remain activated until
the temperature is less than or equal to T
HIGH
. T
LOW
is
disabled.
DS100072-16
*
Note:
Interrupt resets occur only when interrupt Status Register 1 is read.
FIGURE 11. Normal Repetitive Interrupt Response
Diagram
DS100072-17
*
Note:
Interrupt resets occur only when interrupt Status Register 1 is read.
FIGURE 12. One-Time Interrupt Response Diagram
DS100072-18
*
Note:
Interrupt resets occur only when interrupt Status Register 1 is read.
FIGURE 13. Normal Comparator Mode
L
www.national.com
20
相關PDF資料 |
PDF描述 |
|---|---|
| LM81BIMTX-3 | DATA ACQ SYSTEM|6-CHANNEL|8-BIT|TSSOP|24PIN|PLASTIC |
| LM81CIMTX-3 | Single-Ended Data Acquisition System |
| LM8362_SERIES | |
| LM8363_SERIES | |
| LM8368_SERIES | |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM81BIMT-3/NOPB | 功能描述:監控電路 Improved Syst HW Mon RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| LM81BIMT-3/NOPB | 制造商:Texas Instruments 功能描述:, Resolution (Bits):8, Data Interface:Se |
| LM81BIMTX-3 | 功能描述:監控電路 RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| LM81BIMTX-3/NOPB | 功能描述:監控電路 RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| LM81C1MTX-3 | 制造商:Texas Instruments 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。