參數資料
型號： LM81
廠商： National Semiconductor Corporation
英文描述： Serial Interface ACPI-Compatible Microprocessor System
中文描述： 串行接口ACPI的兼容微處理器系統
文件頁數： 3/32頁
文件大?。?/td> 412K
代理商： LM81
Pin Description
(Continued)
Pin
Name(s)
Pin
Number
4
5-6
7
Number
of Pins
1
2
1
Type
Description
SMBCLK
FAN1-FAN2
CI
Digital Input
Digital Inputs
Digital I/O
Serial Bus Clock.
Schmitt Trigger fan tachometer inputs.
An active high input from an external circuit which latches a
Chassis Intrusion event. This line can go high without any
clamping action regardless of the powered state of the LM81.
There is also an internal open-drain output on this line, controlled
by Bit 6 of the Configuration Register (40h) or Bit 7 CI Clear
Register (46h), to provide a minimum 20 ms reset pulse. See
Section 3.3 and Section 9.0
Critical Temperature Alarm active low open-drain output. This pin
can be grounded when not used.
+3.3V V
+
power. Bypass with the parallel combination of 10 μF
(electrolytic or tantalum) and 0.1 μF (ceramic) bypass capacitors.
Interrupt active low open-drain output. This output is enabled when
Bit 1 in the Configuration Register is set to 1. The default state is
disabled.
0V to +1.25V amplitude 8-bit DAC output. When forced high by an
external voltage the NAND Tree Test mode is enabled which
provides board-level connectivity testing. Refer to Section 11.0 on
NAND Tree testing.
Master Reset, 5 mA driver (open-drain), active low output with a
20 ms minimum pulse width. Available when enabled via Bit 4 in
the Configuration register. It acts as an active low power on
RESET input.
Internally connected to all circuitry. The ground reference for all
analog inputs and the DAC output. This pin needs to be
connected to a low noise analog ground plane for optimum
performance of the DAC output.
Analog input for monitoring 12V or Vccp2. Selectable by
choosing the appropriate external resistor divider values such that
the input to the LM81 is scaled to +2.5V. See Section 4.0.
Analog input for monitoring +12V.
Analog input for monitoring +5V.
Analog input for monitoring +3.3V.
Analog input for monitoring +2.5V.
Analog input for monitoring Vccp, a processor voltage that is
nominally at +2.5V.
Supply Voltage readouts from the Pentium/PRO power supplies
that indicate the operating voltage or the processor (e.g. 1.5V to
2.9V). The values are read in the VID/Fan Divisor Register and
the VID4 Register.
T_CRIT_A
8
1
Digital Output
V
+
(+2.8V to
+3.8V)
INT
9
1
POWER
10
1
Digital Output
DACOut/NTEST_IN
11
1
Analog
Output/Digital
Input
RESET
12
1
Digital I/O
GND
13
1
GROUND
Vccp2
14
1
Analog Input
+12Vin
+5Vin
+3.3Vin
+2.5Vin
Vccp1
15
16
17
18
19
1
1
1
1
1
Analog Input
Analog Input
Analog Input
Analog Input
Analog Input
VID4-VID0
20-24
5
Digital Inputs
TOTAL PINS
24
www.national.com
3
相關PDF資料
PDF描述
LM81CIMT-31 Serial Interface ACPI-Compatible Microprocessor System
LM82CIMQAX Remote Diode and Local Digital Temperature Sensor with Two-Wire Interface
LM82CIMQA Remote Diode and Local Digital Temperature Sensor with Two-Wire Interface
LM82 Remote Diode and Local Digital Temperature Sensor with Two-Wire Interface
LM8300HVA9 Four Wire Resistive Touchscreen Controller with Brownout
相關代理商/技術參數
參數描述
LM8-1 制造商:Banner Engineering 功能描述:Logic Module; Delayed One-Shot; ,Ranges For Banner Multi-Beam Sensor Blocks 制造商:Banner Engineering 功能描述:3-And 4-Wire Logic Modules
LM81_02 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Serial Interface ACPI-Compatible Microprocessor System Hardware Monitor
LM810 制造商:NSC 制造商全稱:National Semiconductor 功能描述:3-Pin Microprocessor Reset Circuits
LM810A-2.63 E WAF 制造商:Texas Instruments 功能描述:
LM810A-2.93 E WAF 制造商:Texas Instruments 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*