參數資料
型號: LM4918LQ/NOPB
廠商: NATIONAL SEMICONDUCTOR CORP
元件分類: 音頻控制
英文描述: 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, QCC32
封裝: LLP-32
文件頁數: 3/17頁
文件大?。?/td> 646K
代理商: LM4918LQ/NOPB
Application Information (Continued)
mize thermal design may compromise the LM4918’s perfor-
mance and activate unwanted, though necessary, thermal
shutdown protection.
The LM4918LD must have its DAP soldered to a copper pad
on the PCB. The DAP’s PCB copper pad is then, ideally,
connected to a large plane of continuous unbroken copper.
This plane forms a thermal mass, heat sink, and radiation
area. Place the heat sink area on either outside plane in the
case of a two-sided or multi-layer PCB. (The heat sink area
can also be placed on an inner layer of a multi-layer board.
The thermal resistance, however, will be higher.) Connect
the DAP copper pad to the inner layer or backside copper
heat sink area with 2 vias. The via diameter should be
0.012in - 0.013in with a 1.27mm pitch. Ensure efficient ther-
mal conductivity by plugging and tenting the vias with plating
and solder mask, respectively. Further detailed and specific
information concerning PCB layout, fabrication, and mount-
ing an LQ (LLP) package is available in National Semicon-
ductor’s AN1187.
POWER SUPPLY BYPASSING
As with any power amplifier, proper supply bypassing is
critical for low noise performance and high power supply
rejection. Applications that employ a 5V regulator typically
use a 10F in parallel with a 0.1F filter capacitors to stabi-
lize the regulator’s output, reduce noise on the supply line,
and improve the supply’s transient response. However, their
presence does not eliminate the need for a local 1.0F
tantalum bypass capacitance connected between the
LM4918’s supply pins and ground. Keep the length of leads
and traces that connect capacitors between the LM4918’s
power supply pin and ground as short as possible. Connect-
ing a 2.2F capacitor, C
B, between the BYPASS pin and
ground improves the internal bias voltage’s stability and
improves the amplifier’s PSRR. The PSRR improvements
increase as the bypass pin capacitor value increases. Too
large, however, increases turn-on time and can compromise
the amplifier’s click and pop performance. The selection of
bypass capacitor values, especially C
B, depends on desired
PSRR requirements, click and pop performance system
cost, and size constraints.
200913I8
FIGURE 2. REFERENCE DESIGN BOARD SCHEMATIC
LM4918
www.national.com
11
相關PDF資料
PDF描述
LM4919MM/NOPB 0.014 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO10
LM4921ITLX/NOPB SPECIALTY CONSUMER CIRCUIT, PBGA20
LM4990ITL/NOPB 2 W, 1 CHANNEL, AUDIO AMPLIFIER, PBGA9
LM4990ITLX/NOPB 2 W, 1 CHANNEL, AUDIO AMPLIFIER, PBGA9
LM4995SDX/NOPB 1.25 W, 1 CHANNEL, AUDIO AMPLIFIER, DSO8
相關代理商/技術參數
參數描述
LM4919 制造商:NSC 制造商全稱:National Semiconductor 功能描述:1.5V, Mono 85mW BTL Output, 14mW Stereo Headphone Audio Amplifier
LM4919A WAF 制造商:Texas Instruments 功能描述:
LM4919MM 制造商:Texas Instruments 功能描述:AMP STEREO H/P 1.5V 14MW SMD 4919
LM4919MM/NOPB 功能描述:IC AMP AUDIO MONO/STER AB 10MSOP RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:Boomer® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:DirectDrive® 類型:H 類 輸出類型:耳機,2-通道(立體聲) 在某負載時最大輸出功率 x 通道數量:35mW x 2 @ 16 歐姆 電源電壓:1.62 V ~ 1.98 V 特點:I²C,麥克風,靜音,短路保護,音量控制 安裝類型:表面貼裝 供應商設備封裝:25-WLP(2.09x2.09) 封裝/外殼:25-WFBGA,WLCSP 包裝:帶卷 (TR)
LM4919MMBD 功能描述:BOARDS EVALUATION LM4919MM RoHS:否 類別:編程器,開發系統 >> 評估板 - 音頻放大器 系列:Boomer® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:-