- 您現在的位置：買賣IC網 > PDF目錄367566 > LM4901IBPX AUDIO AMPLIFIER|SINGLE|BGA|8PIN|PLASTIC PDF資料下載
參數資料
| 型號： | LM4901IBPX |
| 英文描述： | AUDIO AMPLIFIER|SINGLE|BGA|8PIN|PLASTIC |
| 中文描述： | 音頻放大器|單| BGA封裝| 8引腳|塑料 |
| 文件頁數： | 13/22頁 |
| 文件大小： | 1177K |
| 代理商： | LM4901IBPX |
Application Information
(Continued)
The LM4901 is unity-gain stable which gives the designer
maximum system flexibility. The LM4901 should be used in
low gain configurations to minimize THD+N values, and
maximize the signal to noise ratio. Low gain configurations
require large input signals to obtain a given output power.
Input signals equal to or greater than 1 Vrms are available
from sources such as audio codecs. Please refer to the
section,
Audio Power Amplifier Design
, for a more com-
plete explanation of proper gain selection.
Besides gain, one of the major considerations is the closed-
loop bandwidth of the amplifier. To a large extent, the band-
width is dictated by the choice of external components
shown in
Figure 1
. The input coupling capacitor, C
, forms a
first order high pass filter which limits low frequency re-
sponse. This value should be chosen based on needed
frequency response for a few distinct reasons.
Selection Of Input Capacitor Size
Large input capacitors are both expensive and space hungry
for portable designs. Clearly, a certain sized capacitor is
needed to couple in low frequencies without severe attenu-
ation. But in many cases the speakers used in portable
systems, whether internal or external, have little ability to
reproduce signals below 100 Hz to 150 Hz. Thus, using a
large input capacitor may not increase actual system perfor-
mance.
In addition to system cost and size, click and pop perfor-
mance is effected by the size of the input coupling capacitor,
C
i.
A larger input coupling capacitor requires more charge to
reach its quiescent DC voltage (nominally 1/2 V
DD
). This
charge comes from the output via the feedback and is apt to
create pops upon device enable. Thus, by minimizing the
capacitor size based on necessary low frequency response,
turn-on pops can be minimized.
Besides minimizing the input capacitor size, careful consid-
eration should be paid to the bypass capacitor value. Bypass
capacitor, C
, is the most critical component to minimize
turn-on pops since it determines how fast the LM4901 turns
on. The slower the LM4901’s outputs ramp to their quiescent
DC voltage (nominally 1/2 V
), the smaller the turn-on pop.
Choosing C
equal to 1.0 μF along with a small value of C
i
(in the range of 0.1 μF to 0.39 μF), should produce a virtually
clickless and popless shutdown function. While the device
will function properly, (no oscillations or motorboating), with
C
equal to 0.1 μF, the device will be much more susceptible
to turn-on clicks and pops. Thus, a value of C
equal to
1.0 μF is recommended in all but the most cost sensitive
designs.
AUDIO POWER AMPLIFIER DESIGN
A 1W/8
Audio Amplifier
Given:
Power Output
Load Impedance
1 Wrms
8
Input Level
Input Impedance
Bandwidth
1 Vrms
20 k
100 Hz–20 kHz
±
0.25 dB
A designer must first determine the minimum supply rail to
obtain the specified output power. By extrapolating from the
Output Power vs Supply Voltage graphs in the
Typical Per-
formance Characteristics
section, the supply rail can be
easily found.
5V is a standard voltage in most applications, it is chosen for
the supply rail. Extra supply voltage creates headroom that
allows the LM4901 to reproduce peaks in excess of 1W
without producing audible distortion. At this time, the de-
signer must make sure that the power supply choice along
with the output impedance does not violate the conditions
explained in the
Power Dissipation
section.
Once the power dissipation equations have been addressed,
the required differential gain can be determined from Equa-
tion 2.
(2)
R
f
/R
i
= A
VD
/2
From Equation 2, the minimum A
VD
is 2.83; use A
VD
= 3.
Since the desired input impedance was 20 k
, and with a
A
impedance of 2, a ratio of 1.5:1 of R
to R
results in an
allocation of R
i
= 20 k
and R
f
= 30 k
. The final design step
is to address the bandwidth requirements which must be
stated as a pair of 3 dB frequency points. Five times away
from a 3 dB point is 0.17 dB down from passband response
which is better than the required
±
0.25 dB specified.
f
L
= 100 Hz/5 = 20 Hz
f
H
= 20 kHz * 5 = 100 kHz
As stated in the
External Components
section, R
i
in con-
junction with C
i
create a highpass filter.
C
i
≥
1/(2
π
*20 k
*20 Hz) = 0.397 μF; use 0.39 μF
The high frequency pole is determined by the product of the
desired frequency pole, f
, and the differential gain, A
.
With a A
= 3 and f
= 100 kHz, the resulting GBWP =
300kHz which is much smaller than the LM4901 GBWP of
2.5MHz. This figure displays that if a designer has a need to
design an amplifier with a higher differential gain, the
LM4901 can still be used without running into bandwidth
limitations.
L
www.national.com
13
相關PDF資料 |
PDF描述 |
|---|---|
| LM4901LD | AUDIO AMPLIFIER|SINGLE|LLCC|10PIN|PLASTIC |
| LM4901MM | AUDIO AMPLIFIER|SINGLE|TSSOP|10PIN|PLASTIC |
| LM627ACJ | Voltage-Feedback Operational Amplifier |
| LM627ACN | Voltage-Feedback Operational Amplifier |
| LM627AMJ | Voltage-Feedback Operational Amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM4901LD | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:AUDIO AMPLIFIER|SINGLE|LLCC|10PIN|PLASTIC |
| LM4901LD/NOPB | 功能描述:IC AMP AUDIO PWR 1.6W MONO 10LLP RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:Boomer® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:DirectDrive® 類型:H 類 輸出類型:耳機，2-通道（立體聲） 在某負載時最大輸出功率 x 通道數量:35mW x 2 @ 16 歐姆 電源電壓:1.62 V ~ 1.98 V 特點:I²C，麥克風，靜音，短路保護，音量控制 安裝類型:表面貼裝 供應商設備封裝:25-WLP（2.09x2.09） 封裝/外殼:25-WFBGA，WLCSP 包裝:帶卷 (TR) |
| LM4901LDX/NOPB | 制造商:Texas Instruments 功能描述:Audio Amp Speaker 1-CH Mono 1.6W Class-AB 10-Pin LLP EP T/R |
| LM4901MM | 制造商:Texas Instruments 功能描述:AMP AUDIO POWER 1W SMD LLP-16 |
| LM4901MM/NOPB | 功能描述:IC AMP AUDIO PWR 1.6W AB 10MSOP RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:Boomer® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:DirectDrive® 類型:H 類 輸出類型:耳機，2-通道（立體聲） 在某負載時最大輸出功率 x 通道數量:35mW x 2 @ 16 歐姆 電源電壓:1.62 V ~ 1.98 V 特點:I²C，麥克風，靜音，短路保護，音量控制 安裝類型:表面貼裝 供應商設備封裝:25-WLP（2.09x2.09） 封裝/外殼:25-WFBGA，WLCSP 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。