- 您現在的位置：買賣IC網 > PDF目錄358866 > LM4873MTE-1 (NATIONAL SEMICONDUCTOR CORP) Dual 2.1W Audio Amplifier Plus Stereo Headphone Function PDF資料下載
參數資料
| 型號： | LM4873MTE-1 |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 音頻／視頻放大 |
| 英文描述： | Dual 2.1W Audio Amplifier Plus Stereo Headphone Function |
| 中文描述： | 3 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO28 |
| 封裝： | 9.70 X 4.40 MM, 0.90 MM HEIGHT, TSSOP-28 |
| 文件頁數： | 14/19頁 |
| 文件大小： | 532K |
| 代理商： | LM4873MTE-1 |
Application Information
(Continued)
NO-LOAD DESIGN CONSIDERATIONS
If the outputs of the LM4873 have a load higher than 10k
,
the LM4873 may show a small oscillation at high output lev-
els. To prevent this oscillation, place 5k
resistors from the
power outputs to ground.
AUDIO POWER AMPLIFIER DESIGN
Design a 1W/8
Bridged Audio Amplifier
Given:
Power Output:
Load Impedance:
Input Level:
Input Impedance:
Bandwidth:
A designer must first determine the minimum supply rail to
obtain the specified output power. By extrapolating from the
Output Power vs Supply Voltage graphs in the
Typical Per-
formance Characteristics
section, the supply rail can be
easily found. A second way to determine the minimum sup-
ply rail is to calculate the required V
opeak
using Equation 3
and add the dropout voltage. Using this method, the mini-
mum supply voltage would be (V
+ (2
*
V
)), where V
is extrapolated from the Dropout Voltage vs Supply Voltage
curve in the
Typical Performance Characteristics
section.
1 Wrms
8
1 Vrms
20 k
100 Hz20 kHz
±
0.25 dB
(4)
Using the Output Power vs Supply Voltage graph for an 8
load, the minimum supply rail is 3.9V. But since 5V is a stan-
dard supply voltage in most applications, it is chosen for the
supply rail. Extra supply voltage creates headroom that al-
lows the LM4873 to reproduce peaks in excess of 1W with-
out producing audible distortion. At this time, the designer
must make sure that the power supply choice along with the
output impedance does not violate the conditions explained
in the
Power Dissipation
section.
Once the power dissipation equations have been addressed,
the required differential gain can be determined from Equa-
tion 4.
(5)
(6)
R
f
/R
i
= A
VD
/2
From equation 4, the minimum A
VD
is 2.83;
Since the desired input impedance was 20 k
, and with a
A
VD
of 3, a ratio of 1.5:1 of R
to R
results in an allocation of
R
= 20 k
and R
= 30 k
. The final design step is to ad-
dress the bandwidth requirements which must be stated as a
pair of 3 dB frequency points. Five times away from a pole
gives 0.17 dB down from passband response, which is better
than the required
±
0.25 dB specified.
f
L
= 100 Hz/5 = 20 Hz
f
H
= 20 kHz x 5 = 100 kHz
As stated in the
External Components
section, R
i
in con-
junction with C
i
create a highpass filter.
use A
VD
= 3
C
i
≥
1/(2
π
*
20 k
*
20 Hz) = 0.397 μF;
The high frequency pole is determined by the product of the
desired high frequency pole, f
H
, and the differential gain, A
VD
. With a A
VD
= 3 and f
H
= 100 kHz, the resulting GBWP =
150 kHz which is much smaller than the LM4873 GBWP of
3.5 MHz. This figure displays that if a designer has a need to
design an amplifier with a higher differential gain, the
LM4873 can still be used without running into bandwidth
problems.
use 0.33 μF
DEMOBOARD CIRCUIT LAYOUT
The demoboard circuit layout is provided here as an ex-
ample of a circuit using the LM4873. If an LM4873MTE is
used with this layout, the exposed-DAP is soldered down to
the copper pad beneath the part. Heat is conducted away
from the part by the two large copper pads in the upper cor-
ners of the demoboard.
This demoboard provides enough heat dissipation ability to
allow an LM4873MTE to output 1.9W into 4
at 25C.
DS100993-93
Silk Screen Layer
DS100993-91
Component-side Copper Layers
L
www.national.com
14
相關PDF資料 |
PDF描述 |
|---|---|
| LM4873MT | Dual 2.1W Audio Amplifier Plus Stereo Headphone Function |
| LM4873MTE | Dual 2.1W Audio Amplifier Plus Stereo Headphone Function |
| LM4873 | Dual 2.1W Audio Amplifier Plus Stereo Headphone Function |
| LM4875 | 750 mW Audio Power Amplifier with DC Volume Control and Headphone Switch |
| LM4875M | 750 mW Audio Power Amplifier with DC Volume Control and Headphone Switch |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM4873MTE-1/NOPB | 制造商:Texas Instruments 功能描述:IC AMP AUDIO PWR 3W STER 28TSSOP |
| LM4873MTEX | 功能描述:音頻放大器 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| LM4873MTEX/NOPB | 功能描述:音頻放大器 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| LM4873MTEX-1 | 功能描述:IC AMP AUDIO PWR 3W STER 28TSSOP RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:Boomer® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:DirectDrive® 類型:H 類 輸出類型:耳機，2-通道（立體聲） 在某負載時最大輸出功率 x 通道數量:35mW x 2 @ 16 歐姆 電源電壓:1.62 V ~ 1.98 V 特點:I²C，麥克風，靜音，短路保護，音量控制 安裝類型:表面貼裝 供應商設備封裝:25-WLP（2.09x2.09） 封裝/外殼:25-WFBGA，WLCSP 包裝:帶卷 (TR) |
| LM4873MTX | 功能描述:IC AMP AUDIO PWR 3W STER 20TSSOP RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:Boomer® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:DirectDrive® 類型:H 類 輸出類型:耳機，2-通道（立體聲） 在某負載時最大輸出功率 x 通道數量:35mW x 2 @ 16 歐姆 電源電壓:1.62 V ~ 1.98 V 特點:I²C，麥克風，靜音，短路保護，音量控制 安裝類型:表面貼裝 供應商設備封裝:25-WLP（2.09x2.09） 封裝/外殼:25-WFBGA，WLCSP 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。