- 您現在的位置：買賣IC網 > PDF目錄30754 > LM4863N/NOPB (NATIONAL SEMICONDUCTOR CORP) 1.5 W, 2 CHANNEL, AUDIO AMPLIFIER, PDIP16 PDF資料下載
參數資料
| 型號： | LM4863N/NOPB |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 音頻／視頻放大 |
| 英文描述： | 1.5 W, 2 CHANNEL, AUDIO AMPLIFIER, PDIP16 |
| 封裝： | 0.300 INCH, MDIP-16 |
| 文件頁數： | 4/21頁 |
| 文件大?。?/td> | 1219K |
| 代理商： | LM4863N/NOPB |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁
Application Information (Continued)
BRIDGE CONFIGURATION EXPLANATION
As shown in Figure 1, the LM4863 consists of two pairs of
operational amplifiers, forming a two-channel (channel A and
channel B) stereo amplifier. (Though the following discusses
channel A, it applies equally to channel B.) External resistors
R
f and Ri set the closed-loop gain of Amp1A, whereas two
internal 20k
resistors set Amp2A’s gain at -1. The LM4863
drives a load, such as a speaker, connected between the two
amplifier outputs, -OUTA and +OUTA.
Figure 1 shows that Amp1A’s output serves as Amp2A’s
input. This results in both amplifiers producing signals iden-
tical in magnitude, but 180 out of phase. Taking advantage
of this phase difference, a load is placed between -OUTA
and +OUTA and driven differentially (commonly referred to
as "bridge mode"). This results in a differential gain of
A
VD =2x(Rf /Ri)
(1)
Bridge mode amplifiers are different from single-ended am-
plifiers that drive loads connected between a single amplifi-
er’s output and ground. For a given supply voltage, bridge
mode has a distinct advantage over the single-ended con-
figuration: its differential output doubles the voltage swing
across the load. This produces four times the output power
when compared to a single-ended amplifier under the same
conditions. This increase in attainable output power as-
sumes that the amplifier is not current limited or that the
output signal is not clipped. To ensure minimum output sig-
nal clipping when choosing an amplifier’s closed-loop gain,
refer to the Audio Power Amplifier Design section.
Another advantage of the differential bridge output is no net
DC voltage across the load. This is accomplished by biasing
channel A’s and channel B’s outputs at half-supply. This
eliminates the coupling capacitor that single supply, single-
ended amplifiers require. Eliminating an output coupling ca-
pacitor in a single-ended configuration forces a single-supply
amplifier’s half-supply bias voltage across the load. This
increases internal IC power dissipation and may perma-
nently damage loads such as speakers.
POWER DISSIPATION
Power dissipation is a major concern when designing a
successful single-ended or bridged amplifier. Equation (2)
states the maximum power dissipation point for a single-
ended amplifier operating at a given supply voltage and
driving a specified output load
P
DMAX =(VDD)
2 /(2
π2 R
L) Single-Ended
(2)
However, a direct consequence of the increased power de-
livered to the load by a bridge amplifier is higher internal
power dissipation for the same conditions.
The LM4863 has two operational amplifiers per channel. The
maximum internal power dissipation per channel operating in
the bridge mode is four times that of a single-ended ampli-
fier. From Equation (3), assuming a 5V power supply and an
4
load, the maximum single channel power dissipation is
1.27W or 2.54W for stereo operation.
P
DMAX =4x(VDD)
2 /(2
π2 R
L) Bridge Mode
(3)
The LM4973’s power dissipation is twice that given by Equa-
tion (2) or Equation (3) when operating in the single-ended
01288101
* Refer to the section Proper Selection of External Components, for a detailed discussion of CB size.
FIGURE 1. Typical Audio Amplifier Application Circuit
Pin out shown for DIP and SO packages. Refer to the Connection Diagrams for the pinout of the TSSOP,
Exposed-DAP TSSOP, and Exposed-DAP LLP packages.
LM4863
www.national.com
12
相關PDF資料 |
PDF描述 |
|---|---|
| LM4863LQX/NOPB | 3.2 W, 2 CHANNEL, AUDIO AMPLIFIER, QCC24 |
| LM4864MDC | 0.55 W, 1 CHANNEL, AUDIO AMPLIFIER, UUC13 |
| LM4864MWC | 0.55 W, 1 CHANNEL, AUDIO AMPLIFIER, UUC13 |
| LM4864N/NOPB | 0.675 W, 1 CHANNEL, AUDIO AMPLIFIER, PDIP8 |
| LM4864LD/NOPB | 0.725 W, 1 CHANNEL, AUDIO AMPLIFIER, DSO10 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM4864 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:300 mW Audio Power Amplifier with Shutdown Mode |
| LM4864LD/NOPB | 功能描述:IC AMP AUDIO PWR .725W AB 10LLP RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:Boomer® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:DirectDrive® 類型:H 類 輸出類型:耳機，2-通道（立體聲） 在某負載時最大輸出功率 x 通道數量:35mW x 2 @ 16 歐姆 電源電壓:1.62 V ~ 1.98 V 特點:I²C，麥克風，靜音，短路保護，音量控制 安裝類型:表面貼裝 供應商設備封裝:25-WLP（2.09x2.09） 封裝/外殼:25-WFBGA，WLCSP 包裝:帶卷 (TR) |
| LM4864M | 功能描述:音頻放大器 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| LM4864M | 制造商:Texas Instruments 功能描述:AMP, AUDIO, BOOMER 0.3W, SMD, SOIC8 制造商:Texas Instruments 功能描述:AMP, AUDIO, BOOMER 0.3W, SMD, SOIC8; Amplifier Class:AB; No. of Channels:1; Output Power:725mW; Supply Voltage Range:2.7V to 5.5V; Amplifier Case Style:MSOP; No. of Pins:8; Load Impedance:8ohm; Operating Temperature Min:-40C; ;RoHS Compliant: Yes |
| LM4864M/NOPB | 功能描述:音頻放大器 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。