- 您現在的位置：買賣IC網 > PDF目錄30754 > LM4863N/NOPB (NATIONAL SEMICONDUCTOR CORP) 1.5 W, 2 CHANNEL, AUDIO AMPLIFIER, PDIP16 PDF資料下載
參數資料
| 型號： | LM4863N/NOPB |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 音頻／視頻放大 |
| 英文描述： | 1.5 W, 2 CHANNEL, AUDIO AMPLIFIER, PDIP16 |
| 封裝： | 0.300 INCH, MDIP-16 |
| 文件頁數： | 16/21頁 |
| 文件大?。?/td> | 1219K |
| 代理商： | LM4863N/NOPB |
Electrical Characteristics for Bridged-Mode Operation (Notes 3, 11) (Continued)
The following specifications apply for V
DD= 5V unless otherwise specified. Limits apply for TA= 25C.
Symbol
Parameter
Conditions
LM4863
Units
(Limits)
Typical
Limit
LM4863MTE, R
L =4
LM4863LQ, R
L =4
2.7
W
LM4863, R
L =8
1.5
W
THD+N = 1%, f = 1kHz, R
L =32
0.34
W
THD+N
Total Harmonic Distortion+Noise
20Hz
≤ f ≤ 20kHz, A
VD =2
LM4863MTE, R
L =4
,P
O =2W
LM4863LQ, R
L =4
,P
O =2W
0.3 0.3
%
LM4863, R
L =8
,P
O = 1W
0.3
%
PSRR
Power Supply Rejection Ratio
V
DD = 5V, VRIPPLE = 200mVRMS,RL =8
,
C
B = 1.0F
67
dB
X
TALK
Channel Separation
f = 1kHz, C
B = 1.0F
90
dB
SNR
Signal To Noise Ratio
V
DD = 5V, PO = 1.1W, RL =8
98
dB
Electrical Characteristics for Single-Ended Operation (Notes 3, 4)
The following specifications apply for V
DD= 5V unless otherwise specified. Limits apply for TA= 25C.
Symbol
Parameter
Conditions
LM4863
Units
(Limits)
Typical
Limit
V
OS
Output Offset Voltage
V
IN = 0V
5
50
mV (max)
P
O
Output Power
THD+N = 0.5%, f = 1kHz, R
L =32
85
75
mW (min)
THD+N = 1%, f = 1kHz, R
L =8
340
mW
THD+N = 10%, f = 1kHz, R
L =8
440
mW
THD+N
Total Harmonic Distortion+Noise
A
V = 1, PO = 75mW, 20Hz
≤ f ≤ 20kHz,
R
L =32
0.2
%
PSRR
Power Supply Rejection Ratio
C
B = 1.0F, VRIPPLE = 200mV RMS,
f = 1kHz
52
dB
X
TALK
Channel Separation
f = 1kHz, C
B = 1.0F
60
dB
SNR
Signal To Noise Ratio
V
DD = 5V, PO = 340mW, RL =8
95
dB
Note 3: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
functional, but do not guarantee specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which
guarantee specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not guaranteed for parameters where no limit
is given, however, the typical value is a good indication of device performance.
Note 4: The maximum power dissipation is dictated by TJMAX, θ JA, and the ambient temperature TA and must be derated at elevated temperatures. The maximum
allowable power dissipation is PDMAX =(TJMAX T A)/θJA. For the LM4863, TJMAX = 150C. For the θJAs for different packages, please see the Application
Information section or the Absolute Maximum Ratings section.
Note 5: Human body model, 100 pF discharged through a 1.5k
resistor.
Note 6: Machine model, 220pF – 240pF discharged through all pins.
Note 7: The given
θJA is for an LM4863 packaged in an MXA20A with the exposedDAP soldered to an exposed 2in2 area of 1oz printed circuit board copper.
Note 8: The given
θJA is for an LM4863 packaged in an MXA20A with the exposedDAP soldered to an exposed 1in2 area of 1oz printed circuit board copper.
Note 9: The given
θJA is for an LM4863 packaged in an MXA20A with the exposed-DAP not soldered to printed circuit board copper.
Note 10: The given
θJA is for an LM4863 packaged in an LQA24A with the exposedDAP soldered to an exposed 2in2 area of 1oz printed circuit board copper.
Note 11: All voltages are measured with respect to the ground (GND) pins unless otherwise specified.
Note 12: Typicals are measured at 25C and represent the parametric norm.
Note 13: Limits are guaranteed to National’s AOQL (Average Outgoing Quality Level).
Note 14: The quiescent power supply current depends on the offset voltage when a practical load is connected to the amplifier.
Note 15: Output power is measured at the device terminals.
Note 16: When driving 3
or 4 and operating on a 5V supply, the LM4863LQ and LM4863MTE must be mounted to the circuit board that has a minimum of 2.5in2
of exposed, uninterrupted copper area connected to the LLP package’s exposed DAP.
LM4863
www.national.com
4
相關PDF資料 |
PDF描述 |
|---|---|
| LM4863LQX/NOPB | 3.2 W, 2 CHANNEL, AUDIO AMPLIFIER, QCC24 |
| LM4864MDC | 0.55 W, 1 CHANNEL, AUDIO AMPLIFIER, UUC13 |
| LM4864MWC | 0.55 W, 1 CHANNEL, AUDIO AMPLIFIER, UUC13 |
| LM4864N/NOPB | 0.675 W, 1 CHANNEL, AUDIO AMPLIFIER, PDIP8 |
| LM4864LD/NOPB | 0.725 W, 1 CHANNEL, AUDIO AMPLIFIER, DSO10 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM4864 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:300 mW Audio Power Amplifier with Shutdown Mode |
| LM4864LD/NOPB | 功能描述:IC AMP AUDIO PWR .725W AB 10LLP RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:Boomer® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:DirectDrive® 類型:H 類 輸出類型:耳機，2-通道（立體聲） 在某負載時最大輸出功率 x 通道數量:35mW x 2 @ 16 歐姆 電源電壓:1.62 V ~ 1.98 V 特點:I²C，麥克風，靜音，短路保護，音量控制 安裝類型:表面貼裝 供應商設備封裝:25-WLP（2.09x2.09） 封裝/外殼:25-WFBGA，WLCSP 包裝:帶卷 (TR) |
| LM4864M | 功能描述:音頻放大器 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| LM4864M | 制造商:Texas Instruments 功能描述:AMP, AUDIO, BOOMER 0.3W, SMD, SOIC8 制造商:Texas Instruments 功能描述:AMP, AUDIO, BOOMER 0.3W, SMD, SOIC8; Amplifier Class:AB; No. of Channels:1; Output Power:725mW; Supply Voltage Range:2.7V to 5.5V; Amplifier Case Style:MSOP; No. of Pins:8; Load Impedance:8ohm; Operating Temperature Min:-40C; ;RoHS Compliant: Yes |
| LM4864M/NOPB | 功能描述:音頻放大器 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。