- 您現在的位置：買賣IC網 > PDF目錄358866 > LM4680 (National Semiconductor Corporation) 10W High-Efficiency Mono BTL Audio Power Amplifier PDF資料下載
參數資料
| 型號： | LM4680 |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | 10W High-Efficiency Mono BTL Audio Power Amplifier |
| 中文描述： | 10W的高效率單聲道橋接音頻功率放大器 |
| 文件頁數： | 9/11頁 |
| 文件大?。?/td> | 754K |
| 代理商： | LM4680 |
Application Hints
(Continued)
OUTPUT STAGE FILTERING
The LM4680 requires a low pass filter connected between
the amplifier’s bridge output and the load. Figure 1 shows
the recommended LC filter. A minimum value of 27μH is
recommended. As shown in Figure 1, using the values of the
components connected between the amplifier BTL outputs
and the load achieves a 2nd-order lowpass filter response
with a -3dB cutoff frequency of 25kHz.
THD+N MEASUREMENTS AND OUT OF AUDIO BAND
NOISE
THD+N (Total Harmonic Distortion plus Noise) is a very
important parameter by which all audio amplifiers are mea-
sured. Often it is shown as a graph where either the output
power or frequency is changed over the operating range. A
very important variable in the measurement of THD+N is the
bandwidth-limiting filter at the input of the test equipment.
Class D amplifiers, by design, switch their output power
devices at a much higher frequency than the accepted audio
range (20Hz - 20kHz). Alternately switching the output volt-
age between V
and GND allows the LM4680 to operate at
much higher efficiency than that achieved by traditional
Class AB amplifiers. Switching the outputs at high frequency
also increases the out-of-band noise. Under normal circum-
stances the output lowpass filter significantly reduces this
out-of-band noise. If the low pass filter is not optimized for a
given switching frequency, there can be significant increase
in out-of-band noise. THD+N measurements can be signifi-
cantly affected by out-of-band noise, resulting in a higher
than expected THD+N measurement. To achieve a more
accurate measurement of THD, the test equipment’s input
bandwidth of the must be limited. Some common upper filter
points are 22kHz, 30kHz, and 80kHz. The input filter limits
the noise component of the THD+N measurement to a
smaller bandwidth resulting in a more real-world THD+N
value.
Recommended Printed Circuit
Board Layout
Figures 2 through 4 show the recommended two-layer PC
board layout that is optimized for the 14-pin SD-packaged
LM4680 and associated external components. This circuit is
designed for use with an external 12V supply and 8W speak-
ers (or load resistors). This circuit board is easy to use.Apply
12V and ground to the board’s V
and GND terminals,
respectively. Connect speakers (or load resistors) between
the board’s -OUT and +OUT terminals.Apply the input signal
to the input pin labeled -IN.
L
www.national.com
9
相關PDF資料 |
PDF描述 |
|---|---|
| LM4680SD | 10W High-Efficiency Mono BTL Audio Power Amplifier |
| LM4731 | Stereo 25W Audio Power Amplifier with Mute and Standby Modes |
| LM4731TA | Stereo 25W Audio Power Amplifier with Mute and Standby Modes |
| LM4732 | Stereo 50W Audio Power Amplifier with Mute |
| LM4732TA | Stereo 50W Audio Power Amplifier with Mute |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM4680A E WAF | 制造商:Texas Instruments 功能描述: |
| LM4680SD | 制造商:Texas Instruments 功能描述:IC AMP 10W SMD 4680 LLP-14 |
| LM4680SD/NOPB | 功能描述:IC AMP AUDIO PWR 10W MONO 14LLP RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:Boomer® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:DirectDrive® 類型:H 類 輸出類型:耳機，2-通道（立體聲） 在某負載時最大輸出功率 x 通道數量:35mW x 2 @ 16 歐姆 電源電壓:1.62 V ~ 1.98 V 特點:I²C，麥克風，靜音，短路保護，音量控制 安裝類型:表面貼裝 供應商設備封裝:25-WLP（2.09x2.09） 封裝/外殼:25-WFBGA，WLCSP 包裝:帶卷 (TR) |
| LM4680SDBD | 功能描述:BOARD EVALUATION LM4680SD RoHS:否 類別:編程器，開發系統 >> 評估板 - 音頻放大器 系列:Boomer® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- |
| LM4680SDX/NOPB | 功能描述:IC AMP AUDIO PWR 10W MONO 14LLP RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:Boomer® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:DirectDrive® 類型:H 類 輸出類型:耳機，2-通道（立體聲） 在某負載時最大輸出功率 x 通道數量:35mW x 2 @ 16 歐姆 電源電壓:1.62 V ~ 1.98 V 特點:I²C，麥克風，靜音，短路保護，音量控制 安裝類型:表面貼裝 供應商設備封裝:25-WLP（2.09x2.09） 封裝/外殼:25-WFBGA，WLCSP 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。