- 您現在的位置：買賣IC網 > PDF目錄369786 > LM2618 PDF資料下載
參數資料
| 型號： | LM2618 |
| 文件頁數： | 11/19頁 |
| 文件大?。?/td> | 2317K |
| 代理商： | LM2618 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁
Device Information
The LM2612 is a simple, step-down DC-DC converter opti-
mized for powering low-voltage CPUs or DSPs in cell
phones and other miniature battery powered devices. It pro-
vides pin-selectable output voltages of 1.05V, 1.3V, 1.5V or
1.8V from a single 2.8V to 5.5V LiION battery cell. It is
designed for a maximum load current of 400mA (300mA for
B grade).
The device has all three of the pin-selectable operating
modes required for cell phones and other complex portable
devices. Such applications typically spend a small portion of
their time operating at full power. During full power operation,
synchronized or fixed-frequency PWM mode offers full out-
put current capability while minimizing interference to sensi-
tive IF and data acquisition circuits. PWM mode uses syn-
chronous rectification for high efficiency: typically 91% for a
100mA load with 1.8V output, 2.8V input. These applications
spend the remainder of their time in low-current standby
operation or shutdown to conserve battery power. During
standby operation, hysteretic PFM mode reduces quiescent
current to 160μA typ to maximize battery life. Shutdown
mode turns the device off and reduces battery consumption
to 0.02μA (typ.).
The LM2612 offers good performance and a full set of fea-
tures. It is based on a current-mode switching buck
architecture. The SYNC/MODE input accepts an external
clock between 500kHz and 1MHz. The output voltage selec-
tion pins eliminate external feedback resistors. Additional
features include soft-start, current overload protection, over-
voltage protection and thermal shutdown protection.
The LM2612 is constructed using a chip-scale 10-pin micro
SMD package. The micro SMD package offers the smallest
possible size for space critical applications, such as cell
phones. Required external components are only a small
10uH inductor, and tiny 10uF and 22uF ceramic capacitors
for reduced board area.
Circuit Operation
Referring to
Figure 1
,
Figure 2
, and
Figure 3
the LM2612
operates as follows: During the first part of each switching
cycle, the control block in the LM2612 turns on the internal
PFET switch. This allows current to flow from the input
through the inductor to the output filter capacitor and load.
The inductor limits the current to a ramp with a slope of (V
IN
-V
)/L, by storing energy in a magnetic field. During the
second part of each cycle, the controller turns the PFET
switch off, blocking current flow from the input, and then
turns the NFET synchronous rectifier on. In response, the
inductor’s magnetic field collapses, generating a voltage that
forces current from ground through the synchronous rectifier
to the output filter capacitor and load.As the stored energy is
transferred back into the circuit and depleted, the inductor
current ramps down with a slope of V
OUT
/L. If the inductor
current reaches zero before the next cycle, the synchronous
rectifier is turned off to prevent current reversal. The output
filter capacitor stores charge when the inductor current is
high, and releases it when low, smoothing the voltage across
the load.
The output voltage is regulated by modulating the PFET
switch on-time to control the average current sent to the
load. The effect is identical to sending a duty-cycle modu-
lated rectangular wave formed by the switch and synchro-
nous rectifier to a low-pass filter created by the inductor and
output filter capacitor. The output voltage is equal to the
average voltage at the SW pin.
20041803
FIGURE 1. Typical Operating Circuit
L
www.national.com
11
相關PDF資料 |
PDF描述 |
|---|---|
| LM261J | Analog Comparator |
| LM2636M | Voltage-Mode SMPS Controller |
| LM2636MTC | Voltage-Mode SMPS Controller |
| LM2636MTCX | Voltage-Mode SMPS Controller |
| LM2636MX | Voltage-Mode SMPS Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM2618ATL | 功能描述:IC REG BUCK SYNC ADJ 10-USMD RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:3.3V 輸入電壓:4.5 V ~ 24 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:125mA 同步整流器:無 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 包裝:Digi-Reel® 供應商設備封裝:SOT-6 其它名稱:MAX1836EUT33#TG16DKR |
| LM2618ATLX | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:400mA Sub-miniature, High Efficiency, Synchronous PWM & PFM Programmable DC-DC Converter |
| LM2618BTL | 功能描述:IC REG BUCK SYNC ADJ 10-USMD RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:3.3V 輸入電壓:4.5 V ~ 24 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:125mA 同步整流器:無 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 包裝:Digi-Reel® 供應商設備封裝:SOT-6 其它名稱:MAX1836EUT33#TG16DKR |
| LM2618BTL/NOPB | 制造商:Texas Instruments 功能描述: |
| LM2618BTLX | 功能描述:IC REG BUCK SYNC ADJ 0.3A 10USMD RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:3.3V 輸入電壓:4.5 V ~ 24 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:125mA 同步整流器:無 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 包裝:Digi-Reel® 供應商設備封裝:SOT-6 其它名稱:MAX1836EUT33#TG16DKR |
發布緊急采購，3分鐘左右您將得到回復。