- 您現在的位置：買賣IC網 > PDF目錄361024 > LM2599S-ADJ (NATIONAL SEMICONDUCTOR CORP) SIMPLE SWITCHER Power Converter 150 kHz 3A Step-Down Voltage Regulator, with Features PDF資料下載
參數資料
| 型號： | LM2599S-ADJ |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | SIMPLE SWITCHER Power Converter 150 kHz 3A Step-Down Voltage Regulator, with Features |
| 中文描述： | 7.5 A SWITCHING REGULATOR, 173 kHz SWITCHING FREQ-MAX, PSSO7 |
| 封裝： | TO-263, 7 PIN |
| 文件頁數： | 27/31頁 |
| 文件大?。?/td> | 812K |
| 代理商： | LM2599S-ADJ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁第31頁
Application Information
(Continued)
An additional diode is required in this regulator configuration.
Diode D1 is used to isolate input voltage ripple or noise from
coupling through the C
capacitor to the output, under light
or no load conditions. Also, this diode isolation changes the
topology to closely resemble a buck configuration thus pro-
viding good closed loop stability. A Schottky diode is recom-
mended for low input voltages, (because of its lower voltage
drop) but for higher input voltages, a IN5400 diode could be
used.
Because of differences in the operation of the inverting regu-
lator, the standard design procedure is not used to select the
inductor value. In the majority of designs, a 33 μH, 3.5A in-
ductor is the best choice. Capacitor selection can also be
narrowed down to just a few values. Using the values shown
in Figure 26will provide good results in the majority of invert-
ing designs.
This type of inverting regulator can require relatively large
amounts of input current when starting up, even with light
loads. Input currents as high as the LM2599 current limit (ap-
proximately 4.5A) are needed for 2 ms or more, until the out-
put reaches its nominal output voltage. The actual time de-
pends on the output voltage and the size of the output
capacitor. Input power sources that are current limited or
sources that can not deliver these currents without getting
loaded down, may not work correctly. Because of the rela-
tively high startup currents required by the inverting topology,
the Soft-start feature shown in Figure 26 is recommended.
Also shown in Figure 26 are several shutdown methods for
the inverting configuration. With the inverting configuration,
some level shifting is required, because the ground pin of the
regulator is no longer at ground, but is now at the negative
output voltage. The shutdown methods shown accept
ground referenced shutdown signals.
UNDERVOLTAGE LOCKOUT
Some applications require the regulator to remain off until
the input voltage reaches a predetermined voltage. Figure
28contains a undervoltage lockout circuit for a buck configu-
ration, while Figure 29 and 30 are for the inverting types
(only the circuitry pertaining to the undervoltage lockout is
shown). Figure 28 uses a zener diode to establish the
threshold voltage when the switcher begins operating. When
the input voltage is less than the zener voltage, resistors R1
and R2 hold the Shutdown /Soft-start pin low, keeping the
regulator in the shutdown mode. As the input voltage ex-
ceeds the zener voltage, the zener conducts, pulling the
Shutdown /Soft-start pin high, allowing the regulator to begin
switching. The threshold voltage for the undervoltage lockout
feature is approximately 1.5V greater than the zener voltage.
Figure 29 and 30 apply the same feature to an inverting cir-
cuit. Figure 29 features a constant threshold voltage for turn
on and turn off (zener voltage plus approximately one volt). If
hysteresis is needed, the circuit in Figure 30 has a turn ON
voltage which is different than the turn OFF voltage. The
amount of hysteresis is approximately equal to the value of
the output voltage. Since the SD /SS pin has an internal 7V
zener clamp, R2 is needed to limit the current into this pin to
approximately 1 mA when Q1 is on.
NEGATIVE VOLTAGE CHARGE PUMP
Occasionally a low current negative voltage is needed for bi-
asing parts of a circuit. A simple method of generating a
negative voltage using a charge pump technique and the
switching waveform present at the OUT pin, is shown in Fig-
ure 31 This unregulated negative voltage is approximately
equal to the positive input voltage (minus a few volts), and
can supply up to a 600 mA of output current. There is a re-
Inverting Regulator
DS012582-44
FIGURE 27. Maximum Load Current for
Inverting Regulator Circuit
DS012582-45
FIGURE 28. Undervoltage Lockout for a Buck
Regulator
DS012582-47
FIGURE 29. Undervoltage Lockout Without
Hysteresis for an Inverting Regulator
DS012582-46
FIGURE 30. Undervoltage Lockout With
Hysteresis for an Inverting Regulator
L
www.national.com
27
相關PDF資料 |
PDF描述 |
|---|---|
| LM2599 | Octal Buffers/Drivers With 3-State Outputs 20-TSSOP -40 to 85 |
| LM2599S-5.0 | SIMPLE SWITCHER Power Converter 150 kHz 3A Step-Down Voltage Regulator, with Features |
| LM2599T-12 | SIMPLE SWITCHER Power Converter 150 kHz 3A Step-Down Voltage Regulator, with Features |
| LM2599T-3.3 | SIMPLE SWITCHER Power Converter 150 kHz 3A Step-Down Voltage Regulator, with Features |
| LM2599T-5.0 | SIMPLE SWITCHER Power Converter 150 kHz 3A Step-Down Voltage Regulator, with Features |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM2599S-ADJ/NOPB | 功能描述:直流/直流開關轉換器 RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| LM2599SX-12 | 功能描述:直流/直流開關轉換器 RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| LM2599SX-12/NOPB | 功能描述:直流/直流開關轉換器 RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| LM2599SX-3.3 | 功能描述:直流/直流開關轉換器 RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| LM2599SX-3.3/NOPB | 功能描述:直流/直流開關轉換器 RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。