• <big id="lal8e"><s id="lal8e"><i id="lal8e"></i></s></big><table id="lal8e"><optgroup id="lal8e"><samp id="lal8e"></samp></optgroup></table>
    參數資料
    型號: LH155L
    英文描述: Industrial Control IC
    中文描述: 工業控制IC
    文件頁數: 12/51頁
    文件大?。?/td> 288K
    代理商: LH155L
    12
    LH155BA
    Data Write Operation
    n
    n
    n + 4
    n + 1
    n + 1
    n + 2
    n + 2
    n + 3
    n + 4
    n + 3
    D
    7
    -D
    0
    WRB
    Internal
    Bus
    Holder
    WRB
    Data Read Operation
    D
    7
    -D
    0
    WRB
    Address Set
    n Address
    Data Read
    n Address
    Data Read
    n + 1 Address
    Data Read
    n + 2 Address
    Dummy
    Read
    RDB
    n
    ***
    n
    n + 1
    n + 2
    2.2. Access to Display RAM and
    Internal Register
    The LH155BA makes access to display RAM, and
    internal register by data bus D
    7
    to D
    0
    , chip
    selection CSB pin, display RAM/register shifting
    RS pin, and read/write control RDB and WRB pins.
    When CSB is at "H", it is in non-selective state and
    cannot access display RAM and internal registers.
    When making access to them, set CSB to "L".
    The access to either display RAM or internal
    registers can be shifted by RS input.
    RS = "L" : Display RAM data
    RS = "H" : Internal command register
    The data of 8-bit data bus D
    7
    to D
    0
    are written by
    write-operation after address setting through MPU.
    The timing of write is at the rising of WRB for 80-
    family MPU and at the falling of E for 68-family
    MPU respectively.
    Write is internally processed by intermediately
    placing the bus holder in the internal data bus.
    During data writing from MPU, the data are
    temporally held in the bus holder, then they are
    written by the time of the next cycle.
    Since the read sequence of display RAM data is
    limited, note that when address set is made, the
    designated address data are not output to read
    command immediately after the address set, but
    are output when the second data are read,
    resulting in requiring one time dummy read.
    Dummy read is always required one time after
    address set and write cycle.
    相關PDF資料
    PDF描述
    LH1554P LCD Display Driver
    LH1554M LCD Display Driver
    LH1560F 160 OUTPUT LCD SEGMENT / COMMON DRIVER
    LH15A1 LCD driver with built-in RAM for 256-color STN-LCDs
    LH1684F 5 V Drive 240 Outputs TFT-LCD Source Driver
    相關代理商/技術參數
    參數描述
    LH155N 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Industrial Control IC
    LH155P 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Industrial Control IC
    LH155R 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Industrial Control IC
    LH1560 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LCD Display Driver
    LH1560F 制造商:SHARP 制造商全稱:Sharp Electrionic Components 功能描述:160 OUTPUT LCD SEGMENT / COMMON DRIVER