- 您現在的位置：買賣IC網 > PDF目錄369726 > LC898093 PDF資料下載
參數資料
| 型號： | LC898093 |
| 文件頁數： | 9/12頁 |
| 文件大?。?/td> | 68K |
| 代理商： | LC898093 |
No. 6614-9/12
LC898023K
Continued from preceding page.
Pin No.
Pin name
Type
Pin function
185
V
SS
V
DD
REQ
P
Digital system ground (V
SS
)
Digital system power supply (5 V)
186
P
187
B
SCSI connections
188
I/O
B
189
V
SS
V
DD
V
SS
P
Digital system ground (V
SS
)
Digital system power supply (3.3 V)
190
P
191
P
Digital system ground (V
SS
)
Unused
192
NC
193
NC
Unused
194
RAS0
O
195
RAS1
O
DRAM RAS signal outputs
196
RAS2
O
197
LWE
O
DRAM lower write enable
198
V
DD
V
SS
UWE
P
Digital system power supply (3.3 V)
199
P
Digital system ground (V
SS
)
DRAM upper write enable
200
O
201
CAS0
O
DRAM CAS signal output
202
CAS1
O
203
OE
O
DRAM output enable
204
RA0
O
205
RA1
O
CD-ROM encoder/decoder DRAM address lines
206
RA2
O
207
RA3
O
208
V
DD
P
Digital system power supply (3.3 V)
Pin Functions
<SCSI Interface Pins>
BSY, ACK, MSG, SEL, REQ, ATN, RST, I/O, C/D
(input/output)
SCIS bus control.
DB0 to DB7, DBP
(input/output)
SCSI data bus.
<Microcontroller Interface Pins>
CS
(input)
Chip select signal from the microcontroller. The microcontroller interface is active when this pin is low.
RD, WR
(input)
Connect the microcontroller read and write lines to these inputs.
SWAIT
(input)
Wait signal output to the microcontroller. When accessing buffer RAM, the microcontroller must wait if this pin is
low.
SUA0 to SUA7
(input)
Internal register address lines
D0 to D7
(input)
Microcontroller data bus. These pins have built-in pull-up resistors.
INT0, INT1
(output)
Interrupt request signals output to the microcontroller. INT1 can be set to output the ATAPI interrupt by setting
INT1EN (Conf-R11 bit 7)
These are open drain outputs with built-in 80 k
(at room temperature, 5 V) pull-up resistors.
<Buffer RAM Pins>
I/O0 to I/O15
(input/output)
Buffer RAM data bus. These pins have built-in pull-up resistors.
RA0 to RA9
(output)
Buffer RAM address lines.
相關PDF資料 |
PDF描述 |
|---|---|
| LC898093KL | |
| LC898093KW | |
| LC89973 | |
| LC9100_SERIES | |
| LC9103B | ASIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LC898093KL | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
| LC898093KW | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
| LC898094 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:LC898094 |
| LC898105-TBM-GB-E | 功能描述:馬達/運動/點火控制器和驅動器 IMD RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| LC898107AD-TBM-H | 制造商:ON Semiconductor 功能描述:OIS VCM DRIVER - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。