- 您現在的位置：買賣IC網 > PDF目錄369726 > LC898093 PDF資料下載
參數資料
| 型號： | LC898093 |
| 文件頁數： | 10/12頁 |
| 文件大?。?/td> | 68K |
| 代理商： | LC898093 |
RAS0, RAS1, RAS2
(output)
Buffer DRAM RAS outputs. Normally, RAS0 is used. However, if two 16-Mbit DRAMs are used, connect the RAS0
and RAS1 lines to the RAS pins on the DRAMs. If four 16-Mbit DRAMs are used, connect the RAS0, RAS1, RAS2,
and LWE lines to the RAS pins on the DRAMs.
CAS0, CAS1
(output)
Buffer DRAM CAS outputs. Normally, CAS0 is used. However, if two 16-Mbit DRAMs are used, connect the CAS0
output to the CAS pins on the DRAMs. If 2-CAS type DRAMs are used, connect CAS0 to UCAS and CAS1 to
LCAS.
OE
(output)
Buffer RAM read output.
UWE, LWE
(output)
Buffer RAM write outputs. Connect these to the corresponding pins. If 2-CAS type DRAMs are used, UWE must be
connected. (Leave LWE open.)
1. Analog Interface Pins
RREC
(input)
Optical discrimination input.
FE
(input)
Focus error signal input.
TE
(input)
Tracking error signal input.
VREF
(input)
Input for the servo system reference voltage.
AD0, AD1, AD2
(input)
A/D converter auxiliary inputs.
DA0, DA1, DA2
(input)
D/A converter auxiliary inputs.
TES
(input)
TES comparator input.
TDO
(output)
Tracking control signal output.
FDO
(output)
Focus control signal output.
SLDO
(output)
Sled control signal output.
SPDO
(output)
Spindle control signal output.
2. EFM Input Block Pins
EFMIN
(input)
EFM signal input.
The high-frequency components of the RF signal acquired from the RF amplifier are cut with a capacitor, and this
pin inputs that signal biased by the value of the SLCO0 to SLCO3 outputs passed through a low-pass filter.
EFMIN2
(input)
Used to change the time constant of the low-pass filter.
SLCIST1, SLCIST2
(input)
Slice level controller charge pump bias resistor connection.
SLCO0, SLCO1, SLCO2, SLCO3
(output)
Slice level controller charge pump outputs.
These levels bias the RF signal input to the EFMIN pin after being passed through a low-pass filter.
DSLB
(output)
Slice level control PWM output.
EFMO
(output)
Post-binarization EFM signal output. (For monitoring)
No. 6614-10/12
LC898023K
相關PDF資料 |
PDF描述 |
|---|---|
| LC898093KL | |
| LC898093KW | |
| LC89973 | |
| LC9100_SERIES | |
| LC9103B | ASIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LC898093KL | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
| LC898093KW | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
| LC898094 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:LC898094 |
| LC898105-TBM-GB-E | 功能描述:馬達/運動/點火控制器和驅動器 IMD RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| LC898107AD-TBM-H | 制造商:ON Semiconductor 功能描述:OIS VCM DRIVER - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。