參數資料
型號: LC87F2932AU-CD-E
廠商: ON Semiconductor
文件頁數: 24/29頁
文件大?。?/td> 0K
描述: IC MCU 8BIT 32K FLASH 64TQLP
標準包裝: 250
芯體尺寸: 8-位
速度: 12MHz
連通性: SIO,UART/USART
外圍設備: PWM,WDT
輸入/輸出數: 59
程序存儲器容量: 32KB(32K x 8)
程序存儲器類型: 閃存
RAM 容量: 2K x 8
電壓 - 電源 (Vcc/Vdd): 2.2 V ~ 5.5 V
數據轉換器: A/D 13x8b
振蕩器型: 內部
工作溫度: -40°C ~ 85°C
封裝/外殼: *
包裝: *
LC87F2932A
No.A1210-4/29
Oscillation Circuits
RC oscillation circuit (internal):
For system clock
CF oscillation circuit:
For system clock, with internal Rf
Crystal oscillation circuit:
For low-speed system clock, with internal Rf
Frequency variable RC oscillation circuit (internal): For system clock
1) Adjustable in ±4% (typ) step from a selected center frequency.
2) Measures oscillation clock using a input signal from XT1 as a reference.
System Clock Divider Function
Can run on low current.
The minimum instruction cycle selectable from 300ns, 600ns, 1.2μs, 2.4μs, 4.8μs, 9.6μs, 19.2μs, 38.4μs,
and 76.8
μs (at a main clock rate of 10MHz).
Standby Function
HALT mode: Halts instruction execution while allowing the peripheral circuits to continue operation.
1) Oscillation is not halted automatically.
2) There are three ways of resetting the HALT mode.
(1) Setting the reset pin to the low level
(2) System resetting by watchdog timer
(3) Occurrence of an interrupt
HOLD mode: Suspends instruction execution and the operation of the peripheral circuits.
1) The CF, RC, X’tal, and frequency variable RC oscillators automatically stop operation.
2) There are four ways of resetting the HOLD mode.
(1) Setting the reset pin to the low level.
(2) System resetting by watchdog timer
(3) Having an interrupt source established at either INT0, INT1, INT2, INT4, INT5, INT6, or INT7
* INT0 and INT1 HOLD mode reset is available only when level detection is set.
(4) Having an interrupt source established at port 0
X'tal HOLD mode: Suspends instruction execution and the operation of the peripheral circuits except the base timer.
1) The CF, RC, and frequency variable RC oscillators automatically stop operation.
2) The state of crystal oscillation established when the X'tal HOLD mode is entered is retained.
3) There are six ways of resetting the X'tal HOLD mode.
(1) Setting the reset pin to the low level
(2) System resetting by watchdog timer
(3) Having an interrupt source established at either INT0, INT1, INT2, INT4, INT5, INT6, or INT7
* INT0 and INT1 HOLD mode reset is available only when level detection is set.
(4) Having an interrupt source established at port 0
(5) Having an interrupt source established in the base timer circuit
(6) Having an interrupt source established in the day and time counter circuit
On-chip Debugger
Supports software debugging with the IC mounted on the target board (LC87D2932A).
LC87F2932A has an On-chip debugger but its function is limited.
Package Form
QIP64E (14 × 14):
Lead-free type
TQFP64J (7 × 7):
Lead-free type
FLGA68K (6.0 × 6.0): Lead-free type
FLGA64 (5.0 × 5.0):
Lead-free type
Development Tools
On-chip debugger: TCB87- TypeB + LC87D2932A
相關PDF資料
PDF描述
LFECP33E-4FN672I IC FPGA 32.8KLUTS 672FPBGA
LFX200B-05FN256C IC FPGA 200K GATES 256-BGA
LFXP20E-5F484C IC FPGA 19.7KLUTS 340I/O 484-BGA
LPC11C24FBD48/301, IC MCU 32BIT 32KB FLASH 48LQFP
LPC11D14FBD100/302 IC MCU 32BIT 32K 100LQFP
相關代理商/技術參數
參數描述
LC87F2932AUFL68TBM-E 制造商:Sony Semiconductor Solutions Division 功能描述:
LC87F2932AU-TQFP7-E 制造商:ON Semiconductor 功能描述:8-BIT MICROCONTROLLER
LC87F2932AVU-QIP-E 功能描述:8位微控制器 -MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
LC87F2C64A 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:8-bit 1-chip Microcontroller
LC87F2C64AU-QFP-H 功能描述:8位微控制器 -MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT