- 您現在的位置：買賣IC網 > PDF目錄358759 > LC72321 (Sanyo Electric Co.,Ltd.) Single-Chip Microcontroller with PLL and LCD Driver PDF資料下載
參數資料
| 型號： | LC72321 |
| 廠商： | Sanyo Electric Co.,Ltd. |
| 英文描述： | Single-Chip Microcontroller with PLL and LCD Driver |
| 中文描述： | 單片微控制器，帶有PLL和LCD驅動器 |
| 文件頁數： | 9/13頁 |
| 文件大?。?/td> | 234K |
| 代理商： | LC72321 |
No. 4796-9/13
LC72321
Continued from preceding page.
Pin
Pin No.
Function
I/O
I/O circuit type
HCTR
LCTR
ADI
INT
EO1
EO2
SNS
HOLD
RES
XIN
XOUT
TEST1
TEST2
V
DD
V
SS
70
71
69
66
77
78
72
67
68
1
80
2
79
31, 73
76
Universal counter input
The input should be capacitor-coupled.
The input frequency range is from 0.4 to 12 MHz.
This input can be effectively used for FM IF or AM IF counting.
Universal counter input
The input should be capacitor-coupled for input frequencies in
the range 100 to 150 kHz.
Capacitor coupling is not required for input frequencies from
1 Hz to 20 kHz.
This input can be effectively used for AM IF counting.
This pin can also be used as a normal input port.
A/D converter input
A 1.28 ms period is required for a 6-bit sequential comparison
conversion. The full scale input is ((63/96) · V
DD
) for a data
value of 3FH.
External interrupt request input
An interrupt is generated when the INTEN flag is set (by an
SS instruction) and a falling edge is input.
This pin can also be used as a normal input port.
Reference frequency and programmable divisor phase
comparison error outputs
Charge pump circuits are built in.
EO1 and EO2 are the same.
Input pin used to determine if a power outage has occurred in
BACKUP mode
This pin can also be used as a normal input port.
Input pin used to force the LC72322 to HOLD mode
The LC72322 goes to HOLD mode when the HOLDEN flag is
set (by an SS instruction) and the HOLD input goes low.
A high breakdown voltage circuit is used so that this input can
be used in conjunction with the normal power switch.
System reset input
This signal should be held low for 75 ms after power is first
applied to effect a power-up reset.
The reset starts when a low level has been input for at least
six reference clock cycles.
Crystal oscillator connections
(4.5 MHz)
A feedback resistor is built in.
LSI test pins. These pins must be connected to V
SS
.
Power supply
Input
Input
Input
Output
Input
Input
Input
Input
Output
—
—
相關PDF資料 |
PDF描述 |
|---|---|
| LC72322N | Single-Chip Microcontroller with Built-in LCD Driver and PLL Circuits(用于電子調諧的單片微控制器（帶內置LCD驅動器和鎖相環電路 ）) |
| LC72322 | Single-Chip Microcontroller with PLL and LCD Driver |
| LC72323-XXXX | LED RED/AMBR DIFFUSED(WHITE)RND |
| LC72323 | Single-Chip Microcontroller with PLL and LCD Driver |
| LC72323R | Single-Chip Microcontroller with PLL and LCD Driver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LC72321N | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:LC72321N |
| LC72322 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Single-Chip Microcontroller with PLL and LCD Driver |
| LC72322-9271-E | 制造商:ON Semiconductor 功能描述: |
| LC72322N | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:LC72321N |
| LC72322R | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Single-Chip Microcontroller with PLL and LCD Driver |
發布緊急采購，3分鐘左右您將得到回復。