- 您現在的位置：買賣IC網 > PDF目錄358759 > LC72191M (Sanyo Electric Co.,Ltd.) PLL Frequency Synthesizer for Electronic Tuning in Car Stereo Tuners PDF資料下載
參數資料
| 型號： | LC72191M |
| 廠商： | Sanyo Electric Co.,Ltd. |
| 英文描述： | PLL Frequency Synthesizer for Electronic Tuning in Car Stereo Tuners |
| 中文描述： | 鎖相環頻率合成調諧器在汽車音響電子調諧 |
| 文件頁數： | 7/16頁 |
| 文件大?。?/td> | 194K |
| 代理商： | LC72191M |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁
Continued from preceding page.
Note:
*
The high and low level input voltages for the CE, CL, DI, IN0 and IN1 pins are V
IH
= 2.2 to 6.5 V and V
IL
= 0 to 0.7 V, regardless of the power
supply voltage V
DD
.
Control Data Format (serial input data)
The LC72191 control data consists of 36 bits. All 36 bits must be input after power is applied to set up the LC72191
initial state. This is because the last two bits, while being unrelated to user functions, are data that switches the LSI test
modes.
Once the LC72191 has been initialized, the contents of the first 24 bits (D
0
to CTEN) can be changed without changing
the contents of the last 12 bits (R0 to T1) by inputting data to DI in serial data input mode.
No. 3985-7/16
LC72191, 72191M, 72191JM
Pin No.
Symbol
I/O
Type
Function
7
8
16
15
IN0
IN1
HCTR
LCTR
Input
*
Input
Input
Input port
General-purpose
counter
Frequency
measurement signal
input pin
General-purpose
counter
Frequency or period
measurement signal
input pin
The values of the IN0 and IN1 input ports can be converted from parallel to serial and
output from the DO output pin.
HCTR is selected when SC in the serial input data is set to 1.
Input frequency range: 10 to 60 MHz (70 mVrms minimum)
The signal is supplied to a general-purpose 20-bit binary counter after passing through a
divide-by-eight circuit. Therefore, the value of the counter is 1/8 of the frequency actually
input to HCTR.
When HCTR is selected the LC72191 will function in frequency measurement mode
and the measurement period can be selected to be either 12 or 24 ms. (GT = 0: 12 ms,
1: 24 ms)
The result of the measurement (the value of the general-purpose counter) can be output
MSB first from the DO output pin.
LCTR is selected when SC in the serial input data is set to 0.
When SF in the serial input data is set to 1:
— Frequency measurement mode is selected.
— Input frequency range: 15 to 500 kHz (70 mVrms minimum).
— The signal is supplied directly to the general-purpose counter without passing
through the internal divide-by-eight circuit.
— The measurement period is the same as for HCTR.
When SF in the serial input data is set to 0:
— Period measurement mode is selected.
— Input frequency range: 1 Hz to 20 kHz (V
IH
= 0.7 V
DD
minimum, V
IL
= 0.3·V
DD
maximum)
— The measurement can be selected to be for one or two cycles. If two cycle
measurement is selected the input frequency range becomes 2 Hz to 20 kHz.
(GT = 0: one cycle, 1: two cycles)
Measurement results are output in the same manner as HCTR measurement results.
相關PDF資料 |
PDF描述 |
|---|---|
| LC7219 | PLL Frequency Synthesizers |
| LC7219M | PLL Frequency Synthesizers |
| LC7230-8221 | Single-chip PLL and Microcontroller with LCD Driver |
| LC7230-8272 | Single-chip PLL Controller |
| LC7232-8291 | 1-Chip PLL + Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LC72191M-TLM-E | 制造商:ON Semiconductor 功能描述:PLL FREQUENCY SYNTHESIZER - Tape and Reel |
| LC7219M | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:PLL Frequency Synthesizers |
| LC7220 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
| LC7221 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
| LC7222 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。