參數資料
型號： LAN91C100FD(208PQFP)
英文描述： LAN Node Controller
中文描述： 網絡節點控制器
文件頁數： 17/55頁
文件大?。?/td> 482K
代理商： LAN91C100FD(208PQFP)
FEAST Fast Ethernet Controller
for PCMCIA and Generic 16-Bit Applications
SMSC DS – LAN91C110 REV. B
Page 17
Rev. 09/05/02
BANK 0
OFFSET
0
NAME
TYPE
SYMBOL
TCR
TRANSMIT CONTROL
REGISTER
READ/WRITE
This register holds bits programmed by the CPU to control some of the protocol transmit options.
HIGH
BYTE
LOOP
0
0
0
LOW
BYTE
0
0
0
SWFDUP - Enables Switched Full Duplex mode. In this mode, transmit state machine is inhibited from recognizing carrier
sense, so deferrals will not occur. Also inhibits collision count, therefore, the collision related status bits in the EPHSR are
not valid (CTR_ROL, LATCOL, SQET, 16COL, MUL COL, and SNGL COL). Uses COL100 as flow control, limiting
backoff and jam to 1 clock each before inter-frame gap, then retry will occur after IFG. If COL100 is active during
preamble, full preamble will be output before jam. When SWFDUP is high, the values of FDUPLX and MON_CSN have
no effect. This bit should be low for non-MII operation.
EPH_LOOP - Internal loopback at the EPH block. Serial data is internally looped back when set. Defaults low. When
EPH_LOOP is high the following transmit outputs are forced inactive: TXD0-TXD3 = 0h, TXEN100 = TXEN = 0, TXD = 1.
The following and external inputs are blocked: CRS=CRS100=0, COL=COL100=0, RX_DV= RX_ER=0.
STP_SQET - Stop transmission on SQET error. If set, stops and disables transmitter on SQE test error. Does not stop on
SQET error and transmits next frame if clear. Defaults low.
FDUPLX - When set the LAN91C110 will cause frames to be received if they pass the address filter regardless of the
source for the frame. When clear the node will not receive a frame sourced by itself. This bit does not control the duplex
mode operation, the duplex mode operation is controlled by the SWFDUP bit.
NOCRC - Does not append CRC to transmitted frames when set. Allows software to insert the desired CRC. Defaults to
zero, namely CRC inserted.
PAD_EN - When set, the LAN91C110 will pad transmit frames shorter than 64 bytes with 00. For TX, CPU should write
the actual BYTE COUNT before padded by the LAN91C110 to the buffer RAM, excludes the padded 00. When this bit is
cleared, the LAN91C110 does not pad frames.
FORCOL - When set, the FORCOL bit will force a collision by not deferring deliberately. This bit is set and cleared only
by the CPU. When TXENA is enabled with no packets in the queue and while the FORCOL bit is set, the LAN91C110 will
transmit a preamble pattern the next time a carrier is seen on the line. If a packet is queued, a preamble and SFD will be
transmitted. This bit defaults low to normal operation. NOTE: The LATCOL bit in the EPHSR, setting up as a result of
FORCOL, will reset TXENA to 0. In order to force another collision, TXENA must be set to 1 again.
TXENA - Transmit enabled when set. Transmit is disabled if clear. When the bit is cleared the LAN91C110 will complete
the current transmission before stopping. When stopping due to an error, this bit is automatically cleared.
SWFDUP
Reserved
EPH
STP
SQET
0
FDUPLX
Reserved
Reserved
NOCRC
0
0
0
0
PAD_EN
Reserved
Reserved
Reserved
Reserved
FORCOL
Reserved
TXENA
0
0
0
0
0
相關PDF資料
PDF描述
LAN91C94 ISA/PCMCIA SINGLE CHIP ETHERNET CONTROLLER WITH RAM
LAN91C110TQFP FEAST FAST ETHERNET CONTROLLER FOR PCMCIA AND GENERIC 16-BIT APPLICATIONS
LAN91C96I NON-PCI SINGLE-CHIP FULL DUPLES ETHERNET CONTROLLER
LAN91C96I-MS NON-PCI SINGLE-CHIP FULL DUPLES ETHERNET CONTROLLER
LAN91C96I-MU NON-PCI SINGLE-CHIP FULL DUPLES ETHERNET CONTROLLER
相關代理商/技術參數
參數描述
LAN91C100FDQFP 制造商:Rochester Electronics LLC 功能描述: 制造商:SMSC 功能描述:
LAN91C100FDREVB 制造商:SMSC 制造商全稱:SMSC 功能描述:FEAST FAST ETHERNET CONTROLLER WITH FULL DUPLEX CAPABILITY
LAN91C100FDREVD 制造商:SMSC 制造商全稱:SMSC 功能描述:FEAST FAST ETHERNET CONTROLLER WITH FULL DUPLEX CAPABILITY
LAN91C100-FD-SS 制造商:SMSC 制造商全稱:SMSC 功能描述:FEAST Fast Ethernet Controller with Full Duplex Capability
LAN91C100FD-SS 功能描述:以太網 IC Non-PCI 10/100 Ethernet MAC RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*