- 您現在的位置：買賣IC網 > PDF目錄383255 > L9823 (意法半導體) Octal Low-Side Driver for bulb, resistive and inductive loads with serial input control, output protection and diagnostic PDF資料下載
參數資料
| 型號： | L9823 |
| 廠商： | 意法半導體 |
| 英文描述： | Octal Low-Side Driver for bulb, resistive and inductive loads with serial input control, output protection and diagnostic |
| 中文描述： | 八路低端的燈泡，電阻和串行輸入控制，輸出保護和診斷感性負載驅動程序 |
| 文件頁數： | 3/12頁 |
| 文件大?。?/td> | 168K |
| 代理商： | L9823 |
3/12
L9823
ABSOLUTE MAXIMUM RATINGS
For voltages and currents applied externally to the device. Exceeding limits may cause damage to the device
.
14
Out 2
Output 2
15
SFPD
SFPD. The Short Fault Protect Disable (SFPD) pin is used to disable the overcurrent latch-OFF.
This feature allows control of incandescent loads where in-rush currents exceed the device's
analog current limits. Essentially the SFPD pin determines whether the L9823 output(s) will
instantly shutdown upon sensing an output short or remain ON in a current limiting mode of
operation until the output short is removed or thermal shutdown is reached. If the SFPD pin is
tied to V
DD
the L9823 output(s) will remain ON in a current limited mode of operation upon
encountering a load short to supply. If the SFPD pin is grounded, a short circuit will immediately
shutdown only the output affected. Other outputs not having a fault condition will operate
normally.
16
VDD
VDD
17
GND
GND
18
GND
GND
19
GND
GND
20
GND
GND
21
NC
Not Connected
22
Reset
Reset. The Reset pin is active low and used to clear the SPI shift register and in doing so sets all
output switches OFF. With the device in a system with an MCU; upon initial system power up,
the MCU holds the Reset pin of the device in a logic low state ensuring all outputs to be OFF
until the VDD pin voltages are adequate for predictable operation. After the L9823 is Reset, the
MCU is ready to assert system control with all output switches initially OFF. The Reset pin is
active low and has an internal pull-down incorporated to ensure operational predictability
should the external pull-down of the MCU open circuit. The internal pull-up is to afford safe and
easy interfacing to the MCU. The Reset pin of the L9823 should be pulled to a logic low state for
a duration of at least 160ns to ensure reliable Reset.
23
Out 1
Output 1
24
Out 0
Output 0
Symbol
Parameter
Value
Unit
V
DD
Supply voltage
-0.3 to 7
V
Inputs and data lines
(CSB, SCLK, SI, Reset, SFPD, SO)
V
IN
Voltage
(CSB, SCLK, SI, Reset, SFPD)
-0.3 to 7
V
SDO
Voltage (SO)
-0.3 to V
DD
+0.3
V
I
IN
Protection diodes current
1)
T
≤
1ms
-20 to 20
1)
mA
Outputs (Out0 ... Out7)
V
OUT Cont
Continuous output voltage
-1.5 to 45
V
N°
Pin
Description
PIN FUNCTION
(continued)
相關PDF資料 |
PDF描述 |
|---|---|
| L9825 | Octal Low-side Driver For Resistive and Inductive Loads With Serial / Parallel Input Control, Output Protection and Diagnostic |
| L9826 | Octal Low-Side Driver for resistive and inductive loads with serial/parallel input control, output protection and diagnostic |
| L9830 | MONOLITHIC LAMP DIMMER |
| L9848 | OCTAL CONFIGURABLE LOW/HIGH SIDE DRIVER |
| L9903 | MOTOR BRIDGE CONTROLLER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L9823013TR | 功能描述:電源開關 IC - 配電 Octal Lowside Driver Bulb, Resistive RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
| L9824 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
| L9824D | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
| L9825 | 功能描述:電源開關 IC - 配電 Octal Low Side RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
| L9825_03 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Octal Low-side Driver For Resistive and Inductive Loads With Serial / Parallel Input Control, Output Protection and Diagnostic |
發布緊急采購，3分鐘左右您將得到回復。