參數資料
型號： L8708H
廠商： ZiLOG, Inc.
英文描述： IR/Low-Voltage Microcontroller
中文描述： 紅外/低電壓微控制器
文件頁數： 18/66頁
文件大小： 599K
代理商： L8708H
Z86L88/81/86/87/89/73
IR/Low-Voltage Microcontroller
18
P R E L I M I N A R Y
DS96LV00800
PIN FUNCTIONS
/DS
(Output, active Low). Data Strobe is activated once for
each external memory transfer. For a READ operation,
data must be available prior to the trailing edge of /DS. For
WRITE operations, the falling edge of /DS indicates that
output data is valid.
/AS
(Output, active Low). Address Strobe is pulsed once
at the beginning of each machine cycle. Address output is
through Port 0/Port 1 for all external programs. Memory
address transfers are valid at the trailing edge of /AS. Un-
der program control, /AS is placed in the high-impedance
state along with Ports 0 and 1, Data Strobe, and
Read/Write.
XTAL1
Crystal 1 (time-based input). This pin connects a
parallel-resonant crystal, ceramic resonator, LC, or RC
network or an external single-phase clock to the on-chip
oscillator input.
XTAL2
Crystal 2 (time-based output). This pin connects a
parallel-resonant, crystal, ceramic resonant, LC, or RC
network to the on-chip oscillator output.
R//W
Read/Write (output, write Low). The R//W signal is
Low when the CCP is writing to the external program or
data memory.
R//RL
(input). This pin, when connected to GND, disables
the internal ROM and forces the device to function as a
ROMless Z8. (Note that, when left unconnected or pulled
high to V
CC
, the part functions normally as a Z8 ROM ver-
sion.)
Port 0
(P07-P00). Port 0 is an 8-bit, bidirectional, CMOS
compatible port. These eight I/O lines are configured un-
der software control as a nibble I/O port, or as an address
port for interfacing external memory. The output drivers
are push-pull. Port 0 can be placed under handshake con-
trol. In this configuration, Port 3, lines P32 and P35 are
used as the handshake control /DAV0 and RDY0. Hand-
shake signal function is dictated by the I/O direction of the
Port 0 upper nibble P07-P04. The lower nibble must have
the same direction as the upper nibble.
For external memory references, Port 0 can provide ad-
dress bits A11-A8 (lower nibble) or A15-A8 (lower and up-
per nibble) depending on the required address space. If
the address range requires 12 bits or less, the upper nibble
of Port 0 can be programmed independently as I/O while
the lower nibble is used for addressing. If one or both nib-
bles are needed for I/O operation, they must be configured
by writing to the Port 0 mode register. After a hardware re-
set, Port 0 is configured as an input port.
Port 0 is set in the high-impedance mode (if selected as an
address output) along with Port 1 and the control signals
/AS, /DS, and R//W through P3M bits D4 and D3(Figure
13).
A ROM mask option is available to program 0.4 V
DD
CMOS trip inputs on P00-P03. This allows direct interface
to mouse/trackball IR sensors.
An optional 200 kOhms pull-up is available as a mask op-
tion on all Port 0 bits with nibble select.
Note:
Internal pull-ups are disabled on any given pin or
group of port pins when programmed into output mode.
相關PDF資料
PDF描述
L88M09T 3.3 to 12 V, 0.5 A Low Dropout Voltage Regulator
L88MS08T 8V 0.5A Low Dropout Voltage Regulators with On/Off Function(輸出電壓為8V，輸出電流為500mA的低壓差電源穩壓器（帶輸出電壓控制的開/關功能）)
L88MS33T 3.3V 0.5A Low Dropout Voltage Regulators with On/Off Function(輸出電壓為3.3V，輸出電流為500mA的低壓差電源穩壓器（帶輸出電壓控制的開/關功能）)
L88R05 5V, 1A Voltage-regulator ICs with Reset Function
L88R05C 5V, 1A Voltage-regulator ICs with Reset Function
相關代理商/技術參數
參數描述
L8711P 制造商:POLYFET 制造商全稱:Polyfet RF Devices 功能描述:SILICON GATE ENHANCEMENT MODE RF POWER LDMOS TRANSISTOR
L8712(FECONLY) 制造商:未知廠家 制造商全稱:未知廠家 功能描述:IC TUBE FOR TO-220 508MM
L871E 制造商:VERMASON 功能描述:END PLUG TO-220 TUBE
L87207304 制造商:Molex 功能描述:
L8721 制造商:Leviton Manufacturing Co 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*