- 您現在的位置：買賣IC網 > PDF目錄383253 > L8150 (意法半導體) Brushless motor predriver PDF資料下載
參數資料
| 型號： | L8150 |
| 廠商： | 意法半導體 |
| 英文描述： | Brushless motor predriver |
| 中文描述： | 無刷電機預驅動 |
| 文件頁數： | 20/37頁 |
| 文件大?。?/td> | 573K |
| 代理商： | L8150 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁
Operating description
L8150
20/37
Figure 10.
Rectangular Drive Pattern (Reverse)
Smooth Drive mode is activated when three consecutive periods shorter than TMAX are
detected and device will keep driving in Smooth mode until an external command is applied
(through FR pin) or motor electrical period becomes longer than the maximum period the
device is able to follow.
Startup
phase (rectangular driving) is activated in one of the following conditions:
when the Period Counter saturates;
when the desired rotation direction (coming from FR command) is different from the
detected rotation direction;
SD = High
→
Low
●
●
●
During all working conditions a
current limitation
circuit is active. It is composed of a
current comparator sensing current flowing in the sense resistor (usually a sense resistor is
connected between the sources of all power low side driver transistors and ground) and of
some control logic.
Current limitation is achieved in three possible ways according to the different motor
situations.
The current limiter control method is a consequence of the rotation speed and the detected
direction of the motor.
Let's divide the possible situations in two different cases:
1.
The motor is rotating and its frequency is lower than the one used to switch between
rectangular and sinusoidal driving pattern
2.
The motor is rotating and its frequency is bigger than the one used to switch between
rectangular and sinusoidal driving pattern
In case 1) even if the detected rotation direction is different from the desired direction, the
current limiter control method is to force two phases to GND and one phase is left in high
impedance state.
In case 2) the possible situations can be the following:
2a) The desired direction is equal to the detected direction and sinusoidal mode is applied,
the current limiter control method is forcing all the phases to GND
HallU
HallV
HallW
OutU
OutV
OutW
相關PDF資料 |
PDF描述 |
|---|---|
| L8202 | MULTIFUNCTION ANALOG ASIC |
| L9222 | CAP CER 470PF 3.15KVDC R3 RAD |
| L9230 | SPI CONTROLLED H-BRIDGE |
| L9230DIE1 | SPI CONTROLLED H-BRIDGE |
| L9230-DIE1 | SPI CONTROLLED H-BRIDGE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L815PW | 制造商:SUPERWORLD 制造商全稱:Superworld Electronics 功能描述:HIGH CURRENT MOLDED POWER INDUCTORS |
| L815PW-100MF | 制造商:SUPERWORLD 制造商全稱:Superworld Electronics 功能描述:HIGH CURRENT MOLDED POWER INDUCTORS |
| L815PW-1R0MF | 制造商:SUPERWORLD 制造商全稱:Superworld Electronics 功能描述:HIGH CURRENT MOLDED POWER INDUCTORS |
| L815PW-1R5MF | 制造商:SUPERWORLD 制造商全稱:Superworld Electronics 功能描述:HIGH CURRENT MOLDED POWER INDUCTORS |
| L815PW-2R2MF | 制造商:SUPERWORLD 制造商全稱:Superworld Electronics 功能描述:HIGH CURRENT MOLDED POWER INDUCTORS |
發布緊急采購，3分鐘左右您將得到回復。