參數資料
型號: L6722
廠商: STMICROELECTRONICS
元件分類: 穩壓器
英文描述: SWITCHING CONTROLLER, 300 kHz SWITCHING FREQ-MAX, QCC36
封裝: 6 X 6 MM, 1 MM PITCH, VFQFPN-36
文件頁數: 34/34頁
文件大?。?/td> 421K
代理商: L6722
Obsolete
Product(s)
- Obsolete
Product(s)
L6722
2 Pins description and connection diagrams
9/34
23
OSC / INH /
FLT
Three functional pin:
OSC: It allows programming the switching frequency FSW of each
channel: the equivalent switching frequency at the load side results in
being tripled.
Frequency is programmed according to the resistor connected from the
pin vs. SGND or VCC with a gain of 4kHz/A (see relevant section for
details). Leaving the pin floating programs a switching frequency of
100kHz per phase (300kHz on the load).
INH: Forced low, the device stops operations with all mosfets OFF: all the
protections are disabled except for Preliminary over voltage. It resets the
device from any latching condition.
FLT: The pin is forced high (5V) to signal an OVP FAULT: to recover from
this condition, cycle VCC or the OSC pin. See Section 10 for details.
24
N.C.
Not Internally Bonded.
25
REF_IN
REFrence INput for the regulation. Connect directly or through a resistor
to the REF_OUT pin. See Section 7.1 for details.
26
REF_OUT
REFrence OUTput. Connect directly or through a resistor to the REF_IN
pin. See Section 7.1 for details.
27, 28
N.C.
Not Internally Bonded.
29
SGND
All the internal references are referred to this pin. Connect to the PCB
Signal Ground.
30
FBR
Remote Buffer Non Inverting Input.
Connect to the positive side of the load to perform remote sense.
See Section 12 for proper layout of this connection.
31
FBG
Remote Buffer Inverting Input.
Connect to the negative side of the load to perform remote sense.
See Section 12 for proper layout of this connection.
32 to 34
ISEN3
to
ISEN1
LS Current Sense Pins.
These pins are used for current balance phase-to-phase as well as for the
system OCP. Connect through a resistor Rg to the relative PHASEx pin.
See Section 6 and Section 9.6 for details.
35
CS+
Droop Current Sense non-inverting input.
Connect through R-C network to the main inductors. See Section 7.1 for
details.
36
CS-
Droop Current Sense inverting input.
Connect through resistor RD to the main inductors common node. See
Section 7.1 for details.
This pin also monitor the feedback disconnection. See Section 9.4 for
details.
PAD
THERMAL
PAD
Thermal pad connects the Silicon substrate and makes good thermal
contact with the PCB to dissipate the power necessary to drive the
external mosfets.
Connect to the PGND plane with several VIAs to improve thermal
conductivity.
Table 1.
Pins description (continued)
Pin#
Name
Function
相關PDF資料
PDF描述
L6722TR SWITCHING CONTROLLER, 300 kHz SWITCHING FREQ-MAX, QCC36
L9407F SPECIALTY ANALOG CIRCUIT, PSFM8
L9942 STEPPER MOTOR CONTROLLER, PDSO36
LA5681FN SWITCHING CONTROLLER, 520 kHz SWITCHING FREQ-MAX, QCC48
LB11620T BRUSHLESS DC MOTOR CONTROLLER, 0.25 A, PDSO24
相關代理商/技術參數
參數描述
L6722TR 功能描述:開關變換器、穩壓器與控制器 3 Phase Controller RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel
L6725 功能描述:開關變換器、穩壓器與控制器 Vltg Mode PWM Controller RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel
L6725_07 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Voltage mode PWM controller with bootstrap anti-discharging system
L6725A 功能描述:開關變換器、穩壓器與控制器 Vltg Mode PWM Controller RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel
L6725ATR 功能描述:開關變換器、穩壓器與控制器 Step-Down Controller RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel