- 您現在的位置：買賣IC網 > PDF目錄69003 > L6722 (STMICROELECTRONICS) SWITCHING CONTROLLER, 300 kHz SWITCHING FREQ-MAX, QCC36 PDF資料下載
參數資料
| 型號： | L6722 |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 穩壓器 |
| 英文描述： | SWITCHING CONTROLLER, 300 kHz SWITCHING FREQ-MAX, QCC36 |
| 封裝： | 6 X 6 MM, 1 MM PITCH, VFQFPN-36 |
| 文件頁數： | 24/34頁 |
| 文件大小： | 421K |
| 代理商： | L6722 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁
Obsolete
Product(s)
- Obsolete
Product(s)
12 Layout guidelines
L6722
30/34
12
Layout guidelines
Since the device manages control functions and high-current drivers, layout is one of the most
important things to consider when designing such high current applications. A good layout
solution can generate a benefit in lowering power dissipation on the power paths, reducing
radiation and a proper connection between signal and power ground can optimize the
performance of the control loops.
Two kind of critical components and connections have to be considered when layouting a VR
based on L6722: power components and connections and small signal components
connections.
12.1
Power components and connections
These are the components and connections where switching and high continuous current flows
from the input to the load. The first priority when placing components has to be reserved to this
power section, minimizing the length of each connection and loop as much as possible. To
minimize noise and voltage spikes (EMI and losses) these interconnections must be a part of a
power plane and anyway realized by wide and thick copper traces: loop must be anyway
minimized. The critical components, i.e. the power transistors, must be close one to the other.
The use of multi-layer printed circuit board is recommended.
Figure 18 shows the details of the power connections involved and the current loops. The input
capacitance (CIN), or at least a portion of the total capacitance needed, has to be placed close
to the power section in order to eliminate the stray inductance generated by the copper traces.
Low ESR and ESL capacitors are preferred, MLCC are suggested to be connected near the HS
drain.
Use proper VIAs number when power traces have to move between different planes on the
PCB in order to reduce both parasitic resistance and inductance. Moreover, reproducing the
same high-current trace on more than one PCB layer will reduce the parasitic resistance
associated to that connection.
Connect output bulk capacitor as near as possible to the load, minimizing parasitic inductance
and resistance associated to the copper trace also adding extra decoupling capacitors along
the way to the load when this results in being far from the bulk capacitor bank.
Gate traces must be sized according to the driver RMS current delivered to the power mosfet.
The device robustness allows managing applications with the power section far from the
controller without losing performances. Anyway, when possible, it is suggested to minimize the
distance between controller and power section.
12.2
Small signal components and connections
These are small signal components and connections to critical nodes of the application as well
as bypass capacitors for the device supply (See Figure 18). Locate the bypass capacitor (VCC
and Bootstrap capacitor) close to the device and refer sensible components such as frequency
and offset setup resistors to SGND. Star grounding is suggested: connect SGND to PGND
plane in a single point to avoid that drops due to the high current delivered causes errors in the
device behavior.
相關PDF資料 |
PDF描述 |
|---|---|
| L6722TR | SWITCHING CONTROLLER, 300 kHz SWITCHING FREQ-MAX, QCC36 |
| L9407F | SPECIALTY ANALOG CIRCUIT, PSFM8 |
| L9942 | STEPPER MOTOR CONTROLLER, PDSO36 |
| LA5681FN | SWITCHING CONTROLLER, 520 kHz SWITCHING FREQ-MAX, QCC48 |
| LB11620T | BRUSHLESS DC MOTOR CONTROLLER, 0.25 A, PDSO24 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L6722TR | 功能描述:開關變換器、穩壓器與控制器 3 Phase Controller RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| L6725 | 功能描述:開關變換器、穩壓器與控制器 Vltg Mode PWM Controller RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| L6725_07 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Voltage mode PWM controller with bootstrap anti-discharging system |
| L6725A | 功能描述:開關變換器、穩壓器與控制器 Vltg Mode PWM Controller RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| L6725ATR | 功能描述:開關變換器、穩壓器與控制器 Step-Down Controller RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。