- 您現在的位置：買賣IC網 > PDF目錄377598 > L642DU12RE (Advanced Micro Devices, Inc.) 128 Megabit (8 M x 16-Bit) CMOS 3.0 Volt-only Uniform Sector Flash Memory with VersatileI/O⑩ Control PDF資料下載
參數資料
| 型號： | L642DU12RE |
| 廠商： | Advanced Micro Devices, Inc. |
| 英文描述： | 128 Megabit (8 M x 16-Bit) CMOS 3.0 Volt-only Uniform Sector Flash Memory with VersatileI/O⑩ Control |
| 中文描述： | 128兆位（8米× 16位）的CMOS 3.0伏特，只有統一閃存部門與VersatileI /輸出⑩控制 |
| 文件頁數： | 12/54頁 |
| 文件大?。?/td> | 520K |
| 代理商： | L642DU12RE |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁
10
Am29LV642D
25022A2 May 5, 2006
D A T A S H E E T
enabled for read access until the command register
contents are altered.
See “VersatileI/O
(V
IO
) Control” for more information.
Refer to the AC Read-Only Operations table for timing
specifications and to Figure 13 for the timing diagram.
I
CC1
in the DC Characteristics table represents the ac-
tive current specification for reading array data.
Writing Commands/Command Sequences
To write a command or command sequence (which in-
cludes programming data to the device and erasing
sectors of memory), the system must drive WE# and
CE# (or CE2#) to V
IL
, and OE# to V
IH
.
The device features an
Unlock Bypass
mode to facili-
tate faster programming. Once the device enters the
Unlock Bypass mode, only two write cycles are re-
quired to program a word, instead of four. The “Word
Program Command Sequence” section has details on
programming data to the device using both standard
and Unlock Bypass command sequences.
An erase operation can erase one sector, multiple sec-
tors, or the entire device. Table 2 indicates the address
space that each sector occupies.
I
CC2
in the DC Characteristics table represents the ac-
tive current specification for the write mode. The AC
Characteristics section contains timing specification
tables and timing diagrams for write operations.
Accelerated Program Operation
The device offers accelerated program operations
through the ACC function. This function is primarily in-
tended to allow faster manufacturing throughput dur-
ing system production.
If the system asserts V
HH
on this pin, the device auto-
matically enters the aforementioned Unlock Bypass
mode, temporarily unprotects any protected sectors,
and uses the higher voltage on the pin to reduce the
time required for program operations. The system
would use a two-cycle program command sequence
as required by the Unlock Bypass mode. Removing
V
HH
from the ACC pin returns the device to normal op-
eration.
Note that the ACC pin must not be at V
HH
for
operations other than accelerated programming, or
device damage may result.
Autoselect Functions
If the system writes the autoselect command se-
quence, the device enters the autoselect mode. The
system can then read autoselect codes from the inter-
nal register (which is separate from the memory array)
on DQ15–DQ0. Standard read cycle timings apply in
this mode. Refer to the Autoselect Mode and Autose-
lect Command Sequence sections for more informa-
tion.
Standby Mode
When the system is not reading or writing to the de-
vice, it can place the device in the standby mode. In
this mode, current consumption is greatly reduced,
and the outputs are placed in the high impedance
state, independent of the OE# input.
The device enters the CMOS standby mode when the
CE#, CE2#, and RESET# pins are all held at V
CC
± 0.3
V. (Note that this is a more restricted voltage range
than V
IH
.) If CE#, CE2#, and RESET# are held at V
IH
,
but not within V
CC
± 0.3 V, the device will be in the
standby mode, but the standby current will be greater.
The device requires standard access time (t
CE
) for
read access when the device is in either of these
standby modes, before it is ready to read data.
If the device is deselected during erasure or program-
ming, the device draws active current until the
operation is completed.
I
CC3
in the DC Characteristics (for Two Am29LV640 de-
vices) table represents the standby current specifica-
tion.
Automatic Sleep Mode
The automatic sleep mode minimizes Flash device en-
ergy consumption. The device automatically enables
this mode when addresses remain stable for t
ACC
+
30 ns. The automatic sleep mode is independent of
the CE#, CE2#, WE#, and OE# control signals. Stan-
dard address access timings provide new data when
addresses are changed. While in sleep mode, output
data is latched and always available to the system.
I
CC4
in the DC Characteristics (for Two Am29LV640 de-
vices) table represents the automatic sleep mode cur-
rent specification.
RESET#: Hardware Reset Pin
The RESET# pin provides a hardware method of re-
setting the device to reading array data. When the RE-
SET# pin is driven low for at least a period of t
RP
, the
device immediately terminates any operation in
progress, tristates all output pins, and ignores all
read/write commands for the duration of the RESET#
pulse. The device also resets the internal state ma-
chine to reading array data. The operation that was in-
terrupted should be reinitiated once the device is
ready to accept another command sequence, to en-
sure data integrity.
Current is reduced for the duration of the RESET#
pulse. When RESET# is held at V
SS
± 0.3 V, the device
draws CMOS standby current (I
CC4
). If RESET# is held
at V
IL
but not within V
SS
± 0.3 V, the standby current
will be greater.
The RESET# pin may be tied to the system reset cir-
cuitry. A system reset would thus also reset the Flash
相關PDF資料 |
PDF描述 |
|---|---|
| L642DU90RI | 128 Megabit (8 M x 16-Bit) CMOS 3.0 Volt-only Uniform Sector Flash Memory with VersatileI/O⑩ Control |
| L642DU12RI | 128 Megabit (8 M x 16-Bit) CMOS 3.0 Volt-only Uniform Sector Flash Memory with VersatileI/O⑩ Control |
| L64360 | Highly Integrated ATM Segmentation and Reassembly (SAR) Engine optimized for internetworking applications(用于優化網絡的高度集成的異步傳輸模式-分段和重組處理芯片) |
| L64364 | Highly Integrated ATM Segmentation and Reassembly (SAR) Engine optimized for internetworking applications(用于優化網絡的高度集成的異步傳輸模式-分段和重組處理芯片) |
| L64381 | 4-Port Ethernet Controller(四端口以太網控制器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L642DU12RI | 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:128 Megabit (8 M x 16-Bit) CMOS 3.0 Volt-only Uniform Sector Flash Memory with VersatileI/O⑩ Control |
| L642DU90RI | 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:128 Megabit (8 M x 16-Bit) CMOS 3.0 Volt-only Uniform Sector Flash Memory with VersatileI/O⑩ Control |
| L642F | 制造商:CRYDOM 制造商全稱:Crydom Inc., 功能描述:Power Modules |
| L643 | 制造商:CRYDOM 制造商全稱:Crydom Inc., 功能描述:Power Modules |
| L64324 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:L64324 Intelligent Ethernet Switch |
發布緊急采購，3分鐘左右您將得到回復。