- 您現在的位置：買賣IC網 > PDF目錄67754 > L5989DTR (STMICROELECTRONICS) 5.06 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO16 PDF資料下載
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁
L5989D
Application information
Doc ID 15778 Rev 3
25/51
Considering
η=1 this function has its maximum in D = 0.5:
Typically CIN is dimensioned to keep the maximum peak-peak voltage across the input filter
in the order of 1% VIN_MAX
6.2
Inductor selection
The inductance value fixes the current ripple flowing through the output capacitor. So the
minimum inductance value in order to have the expected current ripple has to be selected.
The rule to fix the current ripple value is to have a ripple at 20%-40% of the output current.
The inductance value can be calculated by the following equation:
Where TON and TOFF are the on and off time of the internal power switch. The maximum
current ripple, at fixed Vout, is obtained at maximum TOFF that is at minimum duty cycle (see
previous section to calculate minimum duty). So fixing
ΔI
L = 20% to 40% of the maximum
output current, the minimum inductance value can be calculated:
where FSW is the switching frequency 1/(TON + TOFF).
For example for VOUT = 3.3 V, VIN = 12 V, IO = 4 A and FSW = 400 kHz the minimum
inductance value to have
ΔI
L = 30% of IO is about 4.7 H.
The peak current through the inductor is given by:
So if the inductor value decreases, the peak current (that has to be lower than the current
limit of the device) increases. The higher is the inductor value, the higher is the average
output current that can be delivered, without reaching the current limit.
Table 10.
Input capacitors
Manufacture
Series
Cap value (
μF)
Rated voltage (V)
MURATA
GRM31
10
25
GRM55
10
25
TDK
C3225
10
25
C
IN_MIN
I
O
2V
PP_MAX
f
SW
----------------------------------------------
=
ΔI
L
V
IN
V
OUT
–
L
------------------------------ T
ON
V
OUT
L
-------------- T
OFF
==
L
MIN
V
OUT
V
F
+
ΔI
MAX
----------------------------
1D
MIN
–
F
SW
-----------------------
=
I
LPK
,
I
O
ΔI
L
2
--------
+
=
相關PDF資料 |
PDF描述 |
|---|---|
| L5989D | 5.06 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO16 |
| L5991D013TR | 1.5 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16 |
| L6258EX | STEPPER MOTOR CONTROLLER, 1.5 A, PDSO36 |
| L6470PD | STEPPER MOTOR CONTROLLER, 7 A, PDSO36 |
| L6566BTR | 0.8 A POWER FACTOR CONTROLLER, 900 kHz SWITCHING FREQ-MAX, PDSO16 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L5991 | 功能描述:電流型 PWM 控制器 Prog Current Mode RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| L5991_01 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:PRIMARY CONTROLLER WITH STANDBY |
| L5991A | 功能描述:電流型 PWM 控制器 Prog Current Mode RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| L5991AD | 功能描述:開關變換器、穩壓器與控制器 Prog Current Mode RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| L5991AD13TR | 功能描述:電流型 PWM 控制器 Prog Current Mode RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
發布緊急采購，3分鐘左右您將得到回復。