參數資料
型號： KSZ8995XA
廠商： Micrel Inc
文件頁數： 13/51頁
文件大?。?/td> 0K
描述： IC SWITCH 10/100 5PORT 128PQFP
標準包裝： 66
系列： *
類型： *
應用： *
安裝類型： 表面貼裝
封裝/外殼： 128-BFQFP
供應商設備封裝： 128-PQFP（14x20）
包裝： 托盤
產品目錄頁面： 1081 (CN2011-ZH PDF)
配用： 576-1642-ND - BOARD EVALUATION FOR KSZ8995XA
其它名稱： 576-1042
KS8995XA
Micrel, Inc.
M9999-051305
20
May 2005
100BASE-FX Signal Detection
The physical port runs in 100BASE-FX mode if FXSDx >0.6V for ports 4 and 5 only. This signal is internally referenced to
1.25V.The fiber module interface should be set by a voltage divider such that FXSDx ‘H’ is above this 1.25V reference,
indicating signal detect, and FXSDx ‘L’ is below the 1.25V reference to indicate no signal. When FXSDx is below 0.6V then
100BASE-FX mode is disabled.
100BASE-FX Far End Fault
Far end fault occurs when the signal detection is logically false from the receive fiber module. When this occurs, the
transmission side signals the other end of the link by sending 84 1’s followed by a zero in the idle period between frames. The
far end fault may be disabled through register settings.
10BASE-T Transmit
The output 10BASE-T driver is incorporated into the 100BASE-T driver to allow transmission with the same magnetics. They
are internally wave-shaped and pre-emphasized into outputs with a typical 2.3V amplitude. The harmonic contents are at least
27dB below the fundamental when driven by an all-ones Manchester-encoded signal.
10BASE-T Receive
On the receive side, input buffer and level detecting squelch circuits are employed. A differential input receiver circuit and a
PLL perform the decoding function. The Manchester-encoded data stream is separated into clock signal and NRZ data. A
squelch circuit rejects signals with levels less than 400mV or with short pulsewidths in order to prevent noises at the RXP or
RXM input from falsely triggering the decoder. When the input exceeds the squelch limit, the PLL locks onto the incoming signal
and the KS8995XA decodes a data frame. The receiver clock is maintained active during idle periods in between data
reception.
Power Management
The KS8995XA features a per port power down mode. To save power the user can power down ports that are not in use by
setting port control registers or MII control registers. In addition, it also supports full chip power down mode. When activated,
the entire chip will be shutdown.
MDI/MDI-X Auto Crossover
The KS8995XA supports MDI/MDI-X auto crossover. This facilitates the use of either a straight connection CAT-5 cable or a
crossover CAT-5 cable. The auto-sense function will detect remote transmit and receive pairs, and correctly assign the transmit
and receive pairs from the Micrel device. This can be highly useful when end users are unaware of cable types and can also
save on an additional uplink configuration connection. The auto crossover feature may be disabled through the port control
registers.
Auto-Negotiation
The KS8995XA conforms to the auto-negotiation protocol as described by the 802.3 committee. Auto-negotiation allows
unshielded twisted pair (UTP) link partners to select the best common mode of operation. In auto-negotiation the link partners
advertise capabilities across the link to each other. If auto-negotiation is not supported or the link partner to the KS8995XA
is forced to bypass auto-negotiation, then the mode is set by observing the signal at the receiver. This is known as parallel mode
because while the transmitter is sending auto-negotiation advertisements, the receiver is listening for advertisements or a fixed
signal protocol.
The flow for the link set up is depicted in Figure 4.
相關PDF資料
PDF描述
EMM36DKKN CONN EDGECARD 72POS .156 WW
EMM36DKKH CONN EDGECARD 72POS .156 WW
GSA50DTMZ-S273 CONN EDGECARD 100PS R/A .125 SLD
GMA50DTMZ-S273 CONN EDGECARD 100PS R/A .125 SLD
GSA50DTBZ-S273 CONN EDGECARD 100PS R/A .125 SLD
相關代理商/技術參數
參數描述
KSZ8995XA4 功能描述:IC SWITCH 5-PORT 10/100 128PQFP RoHS:是 類別:集成電路 (IC) >> 專用 IC 系列:* 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:調幀器 應用:數據傳輸 安裝類型:表面貼裝 封裝/外殼:400-BBGA 供應商設備封裝:400-PBGA（27x27） 包裝:散裝
KSZ8995XAB3 功能描述:IC SWITCH 5-PORT 10/100 128PQFP RoHS:是 類別:集成電路 (IC) >> 專用 IC 系列:* 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:調幀器 應用:數據傳輸 安裝類型:表面貼裝 封裝/外殼:400-BBGA 供應商設備封裝:400-PBGA（27x27） 包裝:散裝
KSZ8995XA-EVAL 功能描述:以太網開發工具 KSZ8995XA Evaluation Board RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓:
KSZ8995X-EVAL 功能描述:BOARD EVALUATION FOR KSZ8995X RoHS:是 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 類型:MCU 適用于相關產品:Freescale MC68HC908LJ/LK（80-QFP ZIF 插口） 所含物品:面板、纜線、軟件、數據表和用戶手冊 其它名稱:520-1035
KSZ8997 功能描述:以太網 IC 8 Port 10/100 Switch with PHY and Frame Buffers (Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*