- 您現在的位置：買賣IC網 > PDF目錄11593 > KSZ8893FQL-FX (Micrel Inc)IC SWITCH ETH 3PORT 128-PQFP PDF資料下載
參數資料
| 型號： | KSZ8893FQL-FX |
| 廠商： | Micrel Inc |
| 文件頁數： | 38/117頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC SWITCH ETH 3PORT 128-PQFP |
| 標準包裝： | 66 |
| 控制器類型： | 以太網開關控制器 |
| 接口： | MII，RMII，SNI |
| 電源電壓： | 3.1 V ~ 3.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 128-BFQFP |
| 供應商設備封裝： | 128-PQFP（14x20） |
| 包裝： | 托盤 |
| 產品目錄頁面： | 1081 (CN2011-ZH PDF) |
| 配用： | 576-1603-ND - EVAL KIT EXPERIMENTAL KSZ8893MQL |
| 其它名稱： | 576-3273 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁當前第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁
Micrel, Inc.
KSZ8893FQL
October 2007
27
M9999-101607-1.3
10Base-FL Operation
10Base-FL operation is supported on port 1 of the KSZ8893FQL. It conforms to clause 15 and 18 of the IEEE802.3
Standard for 10Base-FL fiber operation. Refer to the Standard for details.
In a typical application, the KSZ8893FQL provides media conversion from 10Base-FL fiber on port 1 to 10Base-T
copper on port 2. Alternatively, port 2 can be substituted with port 3 to directly connect to an external MAC.
Physical Interface
For 10Base-FL operation, port 1 interfaces with an external fiber module to drive 850nm fiber optic links. The interface
connections between the KSZ8893FQL and fiber module are single-ended (common mode). 10Base-FL signal
transmission and reception are done on TXM1 (pin 49) and RXM1 (pin 46), respectively. Refer to Micrel reference
schematic for recommended interface circuit and termination.
Enabling 10Base-FL Mode
To enable 10Base-FL mode, tie FXSD1 (pin 44) high to +3.3V and MUX2 (pin 41) low-to-ground. Port 1 should also be
configured with auto-negotiation disabled, forced to 10Mbps for the speed, and set to either half or full duplex.
Optionally, flow control can be enabled to send out PAUSE frames in full duplex mode.
The 10Base-FL settings use the same strapping pins, MIIM registers and port registers as 10Base-T copper. These
settings are summarized in the following table.
Strapping Pin (#)
MIIM Register #, Bit[#]
Port Register #, Bit[#]
10Base-FL Settings
Auto-Negotiation (disable only)
P1ANEN (30)
Reg. 0, Bit[12]
Reg. 28, Bit[7]
Speed (10Mbps only)
P1SPD (31)
Reg. 0, Bit[13]
Reg. 28, Bit[6]
Duplex (half or full)
P1DPX (32)
Reg. 0, Bit[8]
Reg. 28, Bit[5]
Forced Flow Control (option)
P1FFC (33)
---
Reg. 18, Bit[4]
Table 3. 10Base-FL Configuration
100Base-SX Operation
100Base-SX operation is supported on port 1 of the KSZ8893FQL. It conforms to the TIA/EIA-785 Standard for
100Base-SX fiber operation. Refer to the Standard for details.
In a typical application, the KSZ8893FQL provides media conversion from 100Base-SX fiber on port 1 to 100Base-TX
copper on port 2. Alternatively, port 2 can be substituted with port 3 to directly connect to an external MAC.
Physical Interface
For 100Base-SX operation, port 1 interfaces with an external fiber module to drive 850nm fiber optic links. The interface
connections between the KSZ8893FQL and fiber module are single-ended (common mode). 100Base-SX signal
transmission and reception are done on TXM1 (pin 49) and RXM1 (pin 46), respectively. Refer to Micrel’s reference
schematic for recommended interface circuit and termination.
Enabling 100Base-SX Mode
To enable 100Base-SX mode, tie FXSD1 (pin 44) high to +3.3V and MUX2 (pin 41) low-to-ground. Port 1 should also
be configured with auto-negotiation disabled, forced to 100Mbps for the speed, and set to either half or full duplex.
Optionally, flow control can be enabled to send out PAUSE frames in full duplex mode.
The 100Base-SX settings use the same strapping pins, MIIM registers and port registers as 100Base-TX copper. These
settings are summarized in the following table.
相關PDF資料 |
PDF描述 |
|---|---|
| PIC12C509AT-04E/SN | IC MCU OTP 1KX12 8SOIC |
| PIC16F1829T-I/SS | MCU PIC 14K FLASH 1K RAM 20SSOP |
| V72A24C400BL3 | CONVERTER MOD DC/DC 24V 400W |
| PIC16F677-E/SS | IC PIC MCU FLASH 2KX14 20SSOP |
| V72A24C400BL2 | CONVERTER MOD DC/DC 24V 400W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KSZ8893FQLI-FX | 功能描述:以太網 IC 3-Port Ethernet Switch w MII/RMII Interface + 100FX (I-Temp, Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8893MBL | 功能描述:以太網 IC 2+1 Port 10/100 Switch w/Tranceivers & Frame Buffers, 128-Ld PQFP(Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8893MBL TR | 功能描述:以太網 IC 2+1 Port 10/100 Switch w/Tranceivers & Frame Buffers, 100-Ball LFBGA (Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8893MBLI | 功能描述:以太網 IC 2+1 Port 10/100 Switch w/ Tranceivers & Frame Buffers (Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8893MQL | 功能描述:以太網 IC 2+1 Port 10/100 Switch w/Tranceivers & Frame Buffers, 128-Ld PQFP(Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。