參數資料
型號： KSZ8863FLLI
廠商： Micrel Inc
文件頁數： 47/106頁
文件大小： 0K
描述： IC ETHERNET SWITCH 3PORT 48-LQFP
標準包裝： 250
控制器類型： 以太網開關控制器
接口： MII
電源電壓： 1.8V，2.5V，3.3V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 48-LQFP
供應商設備封裝： 48-LQFP（7x7）
包裝： 托盤
配用： 576-3866-ND - BOARD EVALUATION FOR KSZ8863FLL
其它名稱： 576-3750
PIC16C72 Series
DS39016A-page 44
Preliminary
1998 Microchip Technology Inc.
FIGURE 8-5:
SSPCON: SYNC SERIAL PORT CONTROL REGISTER (ADDRESS 14h) (PIC16CR72)
R/W-0
WCOL
SSPOV
SSPEN
CKP
SSPM3
SSPM2
SSPM1
SSPM0
R = Readable bit
W = Writable bit
U = Unimplemented bit,
read as ‘0’
- n =Value at POR reset
bit7
bit0
bit 7:
WCOL: Write Collision Detect bit
1 = The SSPBUF register is written while it is still transmitting the previous word
(must be cleared in software)
0 = No collision
bit 6:
SSPOV: Receive Overow Indicator bit
In SPI mode
1 = A new byte is received while the SSPBUF register is still holding the previous data. In case of over-
ow, the data in SSPSR is lost. Overow can only occur in slave mode. The user must read the SSPBUF,
even if only transmitting data, to avoid setting overow. In master operation, the overow bit is not set
since each new reception (and transmission) is initiated by writing to the SSPBUF register.
0 = No overow
In I2C mode
1 = A byte is received while the SSPBUF register is still holding the previous byte. SSPOV is a "don’t
care" in transmit mode. SSPOV must be cleared in software in either mode.
0 = No overow
bit 5:
SSPEN: Synchronous Serial Port Enable bit
In SPI mode
1 = Enables serial port and congures SCK, SDO, and SDI as serial port pins
0 = Disables serial port and congures these pins as I/O port pins
In I2C mode
1 = Enables the serial port and congures the SDA and SCL pins as serial port pins
0 = Disables serial port and congures these pins as I/O port pins
In both modes, when enabled, these pins must be properly congured as input or output.
bit 4:
CKP: Clock Polarity Select bit
In SPI mode
1 = Idle state for clock is a high level
0 = Idle state for clock is a low level
In I2C mode
SCK release control
1 = Enable clock
0 = Holds clock low (clock stretch) (Used to ensure data setup time)
bit 3-0: SSPM3:SSPM0: Synchronous Serial Port Mode Select bits
0000
= SPI master operation, clock = FOSC/4
0001
= SPI master operation, clock = FOSC/16
0010
= SPI master operation, clock = FOSC/64
0011
= SPI master operation, clock = TMR2 output/2
0100
= SPI slave mode, clock = SCK pin. SS pin control enabled.
0101
= SPI slave mode, clock = SCK pin. SS pin control disabled. SS can be used as I/O pin
0110
= I2C slave mode, 7-bit address
0111
= I2C slave mode, 10-bit address
1011
= I2C firmware controlled master operation (slave idle)
1110
= I2C slave mode, 7-bit address with start and stop bit interrupts enabled
1111
= I2C slave mode, 10-bit address with start and stop bit interrupts enabled
相關PDF資料
PDF描述
PIC16C505-04E/SL IC MCU OTP 1KX12 14SOIC
PIC16F676T-E/ST IC MCU FLASH 1KX14 W/AD 14TSSOP
PIC12LC509A-04I/MF IC MCU OTP 1KX12 LV 8DFN
PIC12LCE519-04/SM IC MCU OTP 1KX12 LV W/EE 8-SOIJ
PIC12CE518T-04I/SM IC MCU OTP 512X12 W/EE 8-SOIC
相關代理商/技術參數
參數描述
KSZ8863MLL 功能描述:以太網 IC 3-Port Copper 10/100 Ethernet Switch with 1x MII Interface (Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8863MLL-EVAL 功能描述:以太網開發工具 3-Port Copper 10/100 Ethernet Switch with 1x MII Interface - Evaluation Board RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓:
KSZ8863MLLI 功能描述:以太網 IC 3-Port Copper 10/100 Ethernet Switch w/ 1x MII Interface (Industrial Grade) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8863RLL 功能描述:以太網 IC 3-Port Copper 10/100 Ethernet Switch with 1x RMII Interface (Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8863RLL-EVAL 功能描述:以太網開發工具 3-Port Copper 10/100 Ethernet Switch with 1x RMII Interface - Evaluation Board RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*