KS8721B/BT Micrel, Inc. Register Map Register No. Description 0h Basic Control Register 1h Basic Status Regis" />
參數資料
型號： KSZ8721BI
廠商： Micrel Inc
文件頁數： 9/32頁
文件大?。?/td> 0K
描述： IC TXRX PHY 10/100 2.5V 48SSOP
標準包裝： 30
類型： 收發器
驅動器/接收器數： 1/1
規程： MII，RMII
電源電壓： 2.375 V ~ 2.625 V
安裝類型： 表面貼裝
封裝/外殼： 48-BSSOP（0.295"，7.50mm 寬）
供應商設備封裝： 48-SSOP
包裝： 管件
產品目錄頁面： 1080 (CN2011-ZH PDF)
配用： 576-1627-ND - BOARD EVALUATION FOR KSZ8721BMC
576-1626-ND - BOARD EVALUATION FOR KSZ8721BL
其它名稱： 576-1027
March 2006
17
M9999-030106
KS8721B/BT
Micrel, Inc.
Register Map
Register No.
Description
0h
Basic Control Register
1h
Basic Status Register
2h
PHY Identier I
3h
PHY Identier II
4h
Auto-Negotiation Advertisement Register
5h
Auto-Negotiation Link Partner Ability Register
6h
Auto-Negotiation Expansion Register
7h
Auto-Negotiation Next Page Register
8h
Link Partner Next Page Ability
15h
RXER Counter Register
1bh
Interrupt Control/Status Register
1fh
100BaseTX PHY Control Register
Address
Name
Description
Mode(Note 1)
Default
Register 0h - Basic Control
0.15
Reset
1 = software reset. Bit is self-clearing
RW/SC
0
0.14
Loop-back
1 = loop-back mode; 0 = normal operation
RW
0
0.13
Speed Select (LSB)
1 = 100Mbps; 0 = 10Mbps
RW
Set by
Ignored if Auto-Negotiation is enabled (0.12 = 1)
SPD100
0.12
Auto-Negotiation Enable
1 = enable auto-negotiation process (override 0.13 and 0.8) RW
Set by
0 = disable auto-negotiation process
NWAYEN
0.11
Power Down
1 = power down mode; 0 = normal operation
RW
0
0.10
Isolate
1 = electrical isolation of PHY from MII and TX+/TX-
RW
Set by ISO
0 = normal operation
0.9
Restart Auto-Negotiation
1 = restart auto-negotiation process
RW/SC
0
0 = normal operation. Bit is self-clearing
0.8
Duplex Mode
1 = full duplex; 0 = half duplex
RW
Set by
DUPLEX
0.7
Collision Test
1 = enable COL test; 0 = disable COL test
RW
0
0.6:1
Reserved
RO
0
0.0
Disable
0 = enable transmitter
R/W
0
Transmitter
1 = disable transmitter
Register 1h - Basic Status
1.15
100BaseT4
1 = T4 capable; 0 = not T4 capable
RO
0
1.14
100BaseTX Full Duplex
1 = capable of 100BaseX full duplex
RO
1
0 = not capable of 100BaseX full duplex
1.13
100BaseTX Half Duplex
1 = capable of 100BaseX half duplex
RO
1
0 = not capable of 100BaseX half duplex
1.12
10BaseT Full Duplex
1 = 10Mbps with full duplex
RO
1
0 = no 10Mbps with full duplex capability
1.11
10BaseT Half Duplex
1 = 10Mbps with half duplex
RO
1
0 = no 10Mbps with half duplex capability
Note 1. RW: Read/Write, RO: Read only, SC: Self clear, LH: Latch High, LL: Latch Low. Some of the default values are set by strap-in. See “Srap-
ping Options.”
Register 0h - Basic Control
0.15
Reset
1 = software reset. Bit is self-clearing
RW/SC
0
0.14
Loop-back
1 = loop-back mode; 0 = normal operation
RW
0
0.13
Speed Select (LSB)
1 = 100Mbps; 0 = 10Mbps
RW
Set by
Ignored if Auto-Negotiation is enabled (0.12 = 1)
SPD100
0.12
Auto-Negotiation Enable
1 = enable auto-negotiation process (override 0.13 and 0.8) RW
Set by
0 = disable auto-negotiation process
NWAYEN
0.10
Isolate
1 = electrical isolation of PHY from MII and TX+/TX-
RW
Set by ISO
0 = normal operation
0.9
Restart Auto-Negotiation
1 = restart auto-negotiation process
RW/SC
0
0 = normal operation. Bit is self-clearing
0.8
Duplex Mode
1 = full duplex; 0 = half duplex
RW
Set by
DUPLEX
0.7
Collision Test
1 = enable COL test; 0 = disable COL test
RW
0
0.6:1
Reserved
RO
0
0.0
Disable
0 = enable transmitter
R/W
0
Transmitter
1 = disable transmitter
Register 1h - Basic Status
1.15
100BaseT4
1 = T4 capable; 0 = not T4 capable
RO
0
1.14
100BaseTX Full Duplex
1 = capable of 100BaseX full duplex
RO
1
0 = not capable of 100BaseX full duplex
1.13
100BaseTX Half Duplex
1 = capable of 100BaseX half duplex
RO
1
0 = not capable of 100BaseX half duplex
1.12
10BaseT Full Duplex
1 = 10Mbps with full duplex
RO
1
0 = no 10Mbps with full duplex capability
1.11
10BaseT Half Duplex
1 = 10Mbps with half duplex
RO
1
0 = no 10Mbps with half duplex capability
0h
Basic Control Register
1h
Basic Status Register
2h
PHY Identier I
3h
PHY Identier II
4h
Auto-Negotiation Advertisement Register
5h
Auto-Negotiation Link Partner Ability Register
6h
Auto-Negotiation Expansion Register
7h
Auto-Negotiation Next Page Register
8h
Link Partner Next Page Ability
15h
RXER Counter Register
1bh
Interrupt Control/Status Register
1fh
100BaseTX PHY Control Register
Register No.
Description
0h
Basic Control Register
1h
Basic Status Register
2h
PHY Identier I
3h
PHY Identier II
4h
Auto-Negotiation Advertisement Register
5h
Auto-Negotiation Link Partner Ability Register
6h
Auto-Negotiation Expansion Register
7h
Auto-Negotiation Next Page Register
8h
Link Partner Next Page Ability
15h
RXER Counter Register
1bh
Interrupt Control/Status Register
1fh
100BaseTX PHY Control Register
Address
Name
Description
Mode
Default
Address
Name
Description
Mode
0.15
Reset
1 = software reset. Bit is self-clearing
RW/SC
0
0.14
Loop-back
1 = loop-back mode; 0 = normal operation
RW
0
0.13
Speed Select (LSB)
1 = 100Mbps; 0 = 10Mbps
RW
Set by
Ignored if Auto-Negotiation is enabled (0.12 = 1)
SPD100
0.12
Auto-Negotiation Enable
1 = enable auto-negotiation process (override 0.13 and 0.8) RW
Set by
0 = disable auto-negotiation process
NWAYEN
0.11
Power Down
1 = power down mode; 0 = normal operation
RW
0
0.10
Isolate
1 = electrical isolation of PHY from MII and TX+/TX-
RW
Set by ISO
0 = normal operation
0.9
Restart Auto-Negotiation
1 = restart auto-negotiation process
RW/SC
0
0 = normal operation. Bit is self-clearing
0.8
Duplex Mode
1 = full duplex; 0 = half duplex
RW
Set by
DUPLEX
0.7
Collision Test
1 = enable COL test; 0 = disable COL test
RW
0
0.6:1
Reserved
RO
0
0.0
Disable
0 = enable transmitter
R/W
0
Transmitter
1 = disable transmitter
0.15
Reset
1 = software reset. Bit is self-clearing
RW/SC
0
0.14
Loop-back
1 = loop-back mode; 0 = normal operation
RW
0
0.13
Speed Select (LSB)
1 = 100Mbps; 0 = 10Mbps
RW
Set by
Ignored if Auto-Negotiation is enabled (0.12 = 1)
SPD100
0.12
Auto-Negotiation Enable
1 = enable auto-negotiation process (override 0.13 and 0.8) RW
Set by
0 = disable auto-negotiation process
NWAYEN
0.11
Power Down
1 = power down mode; 0 = normal operation
RW
0
0.10
Isolate
1 = electrical isolation of PHY from MII and TX+/TX-
RW
Set by ISO
0.9
Restart Auto-Negotiation
1 = restart auto-negotiation process
RW/SC
0
0 = normal operation. Bit is self-clearing
0.8
Duplex Mode
1 = full duplex; 0 = half duplex
RW
Set by
DUPLEX
0.7
Collision Test
1 = enable COL test; 0 = disable COL test
RW
0
0.6:1
Reserved
RO
0
0.0
Disable
0 = enable transmitter
R/W
0
0.15
Reset
1 = software reset. Bit is self-clearing
RW/SC
0
0.14
Loop-back
1 = loop-back mode; 0 = normal operation
RW
0
0.13
Speed Select (LSB)
1 = 100Mbps; 0 = 10Mbps
RW
Set by
Ignored if Auto-Negotiation is enabled (0.12 = 1)
SPD100
0.12
Auto-Negotiation Enable
1 = enable auto-negotiation process (override 0.13 and 0.8) RW
Set by
0 = disable auto-negotiation process
NWAYEN
0.11
Power Down
1 = power down mode; 0 = normal operation
RW
0
0.10
Isolate
1 = electrical isolation of PHY from MII and TX+/TX-
RW
Set by ISO
0 = normal operation
0.9
Restart Auto-Negotiation
1 = restart auto-negotiation process
RW/SC
0
0 = normal operation. Bit is self-clearing
0.8
Duplex Mode
1 = full duplex; 0 = half duplex
RW
Set by
DUPLEX
0.7
Collision Test
1 = enable COL test; 0 = disable COL test
RW
0
0.6:1
Reserved
RO
0
0.0
Disable
0 = enable transmitter
R/W
0
Transmitter
1 = disable transmitter
0.15
Reset
1 = software reset. Bit is self-clearing
RW/SC
0
0.14
Loop-back
1 = loop-back mode; 0 = normal operation
RW
0
0.13
Speed Select (LSB)
1 = 100Mbps; 0 = 10Mbps
RW
Set by
Ignored if Auto-Negotiation is enabled (0.12 = 1)
SPD100
0.12
Auto-Negotiation Enable
1 = enable auto-negotiation process (override 0.13 and 0.8) RW
Set by
0 = disable auto-negotiation process
NWAYEN
0.11
Power Down
1 = power down mode; 0 = normal operation
RW
0
0.10
Isolate
1 = electrical isolation of PHY from MII and TX+/TX-
RW
Set by ISO
0.9
Restart Auto-Negotiation
1 = restart auto-negotiation process
RW/SC
0
0.8
Duplex Mode
1 = full duplex; 0 = half duplex
RW
Set by
DUPLEX
0.7
Collision Test
1 = enable COL test; 0 = disable COL test
RW
0
0.6:1
Reserved
RO
0
0.0
Disable
0 = enable transmitter
R/W
0
1.15
100BaseT4
1 = T4 capable; 0 = not T4 capable
RO
0
1.14
100BaseTX Full Duplex
1 = capable of 100BaseX full duplex
RO
1
0 = not capable of 100BaseX full duplex
1.13
100BaseTX Half Duplex
1 = capable of 100BaseX half duplex
RO
1
0 = not capable of 100BaseX half duplex
1.12
10BaseT Full Duplex
1 = 10Mbps with full duplex
RO
1
0 = no 10Mbps with full duplex capability
1.11
10BaseT Half Duplex
1 = 10Mbps with half duplex
RO
1
0 = no 10Mbps with half duplex capability
1.15
100BaseT4
1 = T4 capable; 0 = not T4 capable
RO
0
1.14
100BaseTX Full Duplex
1 = capable of 100BaseX full duplex
RO
1
1.13
100BaseTX Half Duplex
1 = capable of 100BaseX half duplex
RO
1
1.12
10BaseT Full Duplex
1 = 10Mbps with full duplex
RO
1
1.11
10BaseT Half Duplex
1 = 10Mbps with half duplex
RO
1
1.15
100BaseT4
1 = T4 capable; 0 = not T4 capable
RO
0
1.14
100BaseTX Full Duplex
1 = capable of 100BaseX full duplex
RO
1
0 = not capable of 100BaseX full duplex
1.13
100BaseTX Half Duplex
1 = capable of 100BaseX half duplex
RO
1
0 = not capable of 100BaseX half duplex
1.12
10BaseT Full Duplex
1 = 10Mbps with full duplex
RO
1
0 = no 10Mbps with full duplex capability
1.11
10BaseT Half Duplex
1 = 10Mbps with half duplex
RO
1
0 = no 10Mbps with half duplex capability
1.15
100BaseT4
1 = T4 capable; 0 = not T4 capable
RO
0
1.14
100BaseTX Full Duplex
1 = capable of 100BaseX full duplex
RO
1
1.13
100BaseTX Half Duplex
1 = capable of 100BaseX half duplex
RO
1
1.12
10BaseT Full Duplex
1 = 10Mbps with full duplex
RO
1
1.11
10BaseT Half Duplex
1 = 10Mbps with half duplex
RO
1
相關PDF資料
PDF描述
LT1716CS5#TRMPBF IC COMP OTT R-R 44V TSOT-23-5
LTC490CN8#PBF IC TXRX RS485 LOW POWER 8-DIP
LTC1480CN8#PBF IC TXRX 3.3V RS485 LOWPWR 8-DIP
LT1081CN#PBF IC DVR/RCVR DUAL-RS232 5V 16-DIP
LT1785IS8#PBF IC TXRX RS485/RS422 60V 8-SOIC
相關代理商/技術參數
參數描述
KSZ8721BI TR 功能描述:以太網 IC 10/100 BASE-TX/FX Physical Layer Transceiver, Single 3.3V Supply, 48-SSOP, I-Temp, Lead Free RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8721BL 功能描述:以太網 IC 10/100 Base-TX/FX Physical Layer Transceiver, Single 3.3V Supply, 48-LQFP (Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8721BL A4 制造商:Micrel Inc 功能描述:PHY 1-CH 10Mbps/100Mbps 48-Pin LQFP
KSZ8721BL A4 TR 制造商:Micrel Inc 功能描述:PHY 1-CH 10Mbps/100Mbps 48-Pin LQFP T/R
KSZ8721BL TR 功能描述:以太網 IC 10/100 Base-TX/FX Physical Layer Transceiver, Single 3.3V Supply, 48-LQFP (Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*