參數資料
| 型號： | KSZ8041MLL TR |
| 廠商： | Micrel Inc |
| 文件頁數： | 28/65頁 |
| 文件大?。?/td> | 0K |
| 描述： | TXRX 10/100 3.3V PHY MII 48LQFP |
| 標準包裝： | 1,000 |
| 類型： | 收發器 |
| 驅動器/接收器數： | 1/1 |
| 規程： | MII |
| 電源電壓： | 3.135 V ~ 3.465 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-TQFP |
| 供應商設備封裝： | 48-TQFP（7x7） |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁當前第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁
Micrel, Inc.
KSZ8041TL/FTL/MLL
December 2009
34
M9999-120909-1.2
LinkMD
Cable Diagnostics
The LinkMD
feature utilizes time domain reflectometry (TDR) to analyze the cabling plant for common cabling problems,
such as open circuits, short circuits and impedance mismatches.
LinkMD
works by sending a pulse of known amplitude and duration down the MDI and MDI-X pairs, and then analyzing
the shape of the reflected signal. Timing the pulse duration gives an indication of the distance to the cabling fault with
maximum distance of 200m and accuracy of +/-2m. Internal circuitry computes the TDR information and presents it in a
user-readable digital format.
Note: Cable diagnostics are only valid for copper connections and do not support fiber optic operation.
Access
LinkMD
is initiated by accessing register 1Dh, the LinkMD Control/Status Register, in conjunction with register 1Fh, the
PHY Control 2 Register.
Usage
The following test procedure demonstrates how to use LinkMD
for cable diagnostic:
1.
Disable auto MDI/MDI-X by writing a ‘1’ to register 1Fh bit 13 to enable manual control over the differential pair
used to transmit the LinkMD
pulse.
2.
Select the differential pair to transmit the LinkMD
pulse with register 1Fh bit 14.
3.
Start cable diagnostic test by writing a ‘1’ to register 1Dh bit 15. This enable bit is self-clearing.
4.
Wait (poll) for register 1Dh bit 15 to return a ‘0’, indicating cable diagnostic test is completed.
5.
Read cable diagnostic test results in register 1Dh bits [14:13]. The results are as follows:
00 = normal condition (valid test)
01 = open condition detected in cable (valid test)
10 = short condition detected in cable (valid test)
11 = cable diagnostic test failed (invalid test)
The ‘11’ case, invalid test, occurs if the KSZ8041TL/FTL/MLL is unable to shut down the link partner. In this
instance, the test is not run, since it would be impossible for the KSZ8041TL/FTL/MLL to determine if the detected
signal is a reflection of the signal generated by the KSZ8041TL/FTL/MLL, or a signal from its link partner.
6.
Get distance to fault by multiplying the decimal value in register 1Dh bits [8:0] by a constant of 0.4. The distance,
D (expressed in meters), to the cable fault is determined by the following formula:
D (distance to cable fault) = 0.4 x {decimal value of register 1Dh bits [8:0]}
The 0.4 constant can be calibrated for different cable types and cabling conditions, such as cables with velocity of
propagation that varies significantly from the norm.
Power Management
The KSZ8041TL/FTL/MLL offers the following power management modes:
Power Saving Mode
This mode is used to reduce power consumption when the cable is unplugged. It is in effect when auto-negotiation mode
is enabled, cable is disconnected, and register 1Fh bit 10 is set to 1. Under power saving mode, the KSZ8041TL/FTL/MLL
shuts down all transceiver blocks, except for transmitter, energy detect and PLL circuits. Additionally, in MII mode, the
RXC clock output is disabled. RXC clock is enabled after the cable is connected and link is established.
Power saving mode is disabled by writing a zero to register 1Fh bit 10.
Power Down Mode
This mode is used to power down the entire KSZ8041TL/FTL/MLL device when it is not in use. Power down mode is
enabled by writing a one to register 0h bit 11. In the power down state, the KSZ8041TL/FTL/MLL disables all internal
functions, except for the MII management interface.
相關PDF資料 |
PDF描述 |
|---|---|
| KSZ8041NLA3TR | TRANSCEIVER 10/100 32-MLF |
| KSZ8041NLJ TR | TXRX PHY 10/100 3.3V 32MLF |
| KSZ8041RNL | TXRX 10/100 3.3V PHY RMII 32-MLF |
| KSZ8041TLI TR | IC ETHERNET PHY IND 48TQFP |
| KSZ8051MLL TR | TXRX PHY 10/T100 3.3V MII 48LQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KSZ8041MNLU | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:10Base-T/100Base-TX Physical Layer Transceiver |
| KSZ8041MNLU TR | 功能描述:TXRX PHY 100BASE TX 3.3V 32QFN RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:收發器 驅動器/接收器數:1/1 規程:RS422，RS485 電源電壓:4.75 V ~ 5.25 V 安裝類型:通孔 封裝/外殼:8-DIP（0.300"，7.62mm） 供應商設備封裝:8-PDIP 包裝:管件 產品目錄頁面:1402 (CN2011-ZH PDF) |
| KSZ8041NL | 制造商:Micrel Inc 功能描述:10BASE-T/100BASE ETHERNET TRX SMD 制造商:Micrel Inc 功能描述:10BASE-T/100BASE ETHERNET TRX, SMD 制造商:Micrel Inc 功能描述:10BASE-T/100BASE ETHERNET TRX, SMD, Data Rate:100Mbps, Ethernet Type:IEEE 802.3u 制造商:Micrel Inc 功能描述:10BASE-T/100BASE ETHERNET TRX, SMD, Data Rate:100Mbps, Ethernet Type:IEEE 802.3u, Supply Voltage Max:3.3V, Digital IC Case Style:QFN, No. of Pins:32, IC Interface Type:MII, RMII, MSL:MSL 2 - 1 year, SVHC:No SVHC (19-Dec-2012), Base , RoHS Compliant: Yes |
| KSZ8041NL AM | 功能描述:以太網 IC Physical Layer Transceiver 10/100BASE-T/TX (Lead Free) - Automotive Qualified RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8041NL AM TR | 功能描述:以太網 IC Physical Layer Transceiver 10/100BASE-T/TX (Lead Free) - Automotive Qualified RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。