Each V
參數資料
型號: KMPC870VR80
廠商: Freescale Semiconductor
文件頁數: 8/84頁
文件大?。?/td> 0K
描述: IC MPU POWERQUICC 80MHZ 256PBGA
標準包裝: 2
系列: MPC8xx
處理器類型: 32-位 MPC8xx PowerQUICC
速度: 80MHz
電壓: 3.3V
安裝類型: 表面貼裝
封裝/外殼: 256-BGA
供應商設備封裝: 256-PBGA(23x23)
包裝: 托盤
MPC875/MPC870 PowerQUICC Hardware Specifications, Rev. 4
16
Freescale Semiconductor
Layout Practices
10 Layout Practices
Each VDD pin on the MPC875/MPC870 should be provided with a low-impedance path to the board’s
supply. Each GND pin should likewise be provided with a low-impedance path to ground. The power
supply pins drive distinct groups of logic on chip. The V
DD power supply should be bypassed to ground
using at least four 0.1-F bypass capacitors located as close as possible to the four sides of the package.
Each board designed should be characterized and additional appropriate decoupling capacitors should be
used if required. The capacitor leads and associated printed-circuit traces connecting to chip VDD and
GND should be kept to less than half an inch per capacitor lead. At a minimum, a four-layer board
employing two inner layers as VDD and GND planes should be used.
All output pins on the MPC875/MPC870 have fast rise and fall times. Printed circuit (PC) trace
interconnection length should be minimized in order to minimize undershoot and reflections caused by
these fast output switching times. This recommendation particularly applies to the address and data buses.
Maximum PC trace lengths of 6 inches are recommended. Capacitance calculations should consider all
device loads as well as parasitic capacitances due to the PC traces. Attention to proper PCB layout and
bypassing becomes especially critical in systems with higher capacitive loads because these loads create
higher transient currents in the VDD and GND circuits. Pull up all unused inputs or signals that will be
inputs during reset. Special care should be taken to minimize the noise levels on the PLL supply pins. For
more information, refer to Section 14.4.3, “Clock Synthesizer Power (VDDSYN, VSSSYN, VSSSYN1),” in
the MPC885 PowerQUICC Family Reference Manual.
PADIR (Port A data direction register)
PADIR[5:9]
PADIR[12:13]
0
PBPAR (Port B pin assignment register)
PBPAR[14:18]
PBPAR[20:22]
0
PBDIR (Port B data direction register)
PBDIR[14:8]
PBDIR[20:22]
0
PCPAR (Port C pin assignment register)
PCPAR[4:5]
PCPAR[8:9]
PCPAR[14]
0
PCDIR (Port C data direction register)
PCDIR[4:5]
PCDIR[8:9]
PCDIR[14]
0
PDPAR (Port D pin assignment register)
PDPAR[3:7]
PDPAR[9:5]
0
PDDIR (Port D data direction register)
PDDIR[3:7]
PDDIR[9:15]
0
Table 7. Mandatory Reset Configuration of MPC875/MPC870 (continued)
Register/Configuration
Field
Value
(Binary)
相關PDF資料
PDF描述
15-47-4053 CONN FFC FEMALE 5POS .100 GOLD
AMC44DTES CONN EDGECARD 88POS .100 EYELET
IDT7009L15PF IC SRAM 1MBIT 15NS 100TQFP
KMPC862TZQ100B IC MPU POWERQUICC 100MHZ 357PBGA
IDT7009L15PFG IC SRAM 1MBIT 15NS 100TQFP
相關代理商/技術參數
參數描述
KMPC870ZT133 功能描述:微處理器 - MPU PQ I HIP6W DUET RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324
KMPC870ZT66 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Hardware Specifications
KMPC870ZT80 功能描述:微處理器 - MPU PQ I HIP6W DUET RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324
KMPC875 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Hardware Specifications
KMPC875CVR133 功能描述:微處理器 - MPU PQ I HIP6W DUET RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324