參數資料
型號： IXPD610
英文描述： Industrial Control IC
中文描述： 工業控制IC
文件頁數： 3/8頁
文件大?。?/td> 182K
代理商： IXPD610
2001 IXYS/DEI All rights reserved
IXDP 610
3
Pin Description IXDP 610PI
Nomenclature of
Digital PWM Controller
Sym. Pin Description
D0
D1
D2
D3
D4
D5
D6
D7
1
2
3
4
5
6
7
8
DATA BUS - the data bus on
the IXDP610 is configured for
input only. Data to be written to
the IXDP610 is placed on data
lines D0 through D7 during a
microprocessor write cycle.
Data is accepted by the
IXDP610 when CHIP SELECT
is low and the WRITE input
goes from a low to a high
state. The SELECT input
determines whether the data
written to the IXDP610 will go
to the Control latch or to the
Pulse Width latch. D0 is the
least significant bit and D7 is
the most significant bit.
GND 9
CIRCUIT GROUND
OUT2 10
OUT1 11 these two outputs provide the
complementary PWM signals.
The base period or cycle time
of these outputs is determined
by the CLOCK and the control
latch.
COMPLEMENTARY OUTPUTS
V
CC
12 POWER SUPPLY (5 V
±
10 %)
CLK 13 CLOCK - the frequency of this
input determines the PWM
base frequency. CLK also
drives the internal state
machines. It has no effect on
any data bus transactions.
ODIS 14 OUTPUT DISABLE - asserting
this Schmitt trigger input forces
the complementary outputs to
be immediately disabled
(OUT1 and OUT2 are forced
low). The complementary
outputs will remain low as long
as long as this input is asser-
ted, and for the duration of the
PWM cycle in which OUTPUT
DISABLE goes from low to
high; i.e., the complementary
outputs are not re-enabled
until the beginning of the next
PWM cycle, and then only if
OUTPUT DISABLE and the
Stop bit in the Control latch are
not asserted.
CS
WR
RST
SEL
ODIS
CLK
V
OUT1
OUT2
D0
D1
D2
D3
D4
D5
D6
D7
GND
SEL 15 SELECT-this input determines
whether data written into the
IXDP610 goes to the internal
Pulse Width (PW) latch or to
the Control latch. A zero on
this input (low voltage) directs
data to the PW latch; a one on
this input (high voltage) directs
data to the Control latch.
RST 16 RESET-this asynchronous,
active low input disables the
outputs, chooses 8-bit count
mode in the PWM counter,
sets the clock to be "divided
by 1", clears Lock bit, and sets
the dead-time counter to 7.
Asserting RESET writes a
01000111 binary to the Control
latch. Asserting RESET is the
only way in which the Lock bit
in the control latch can be
cleared. Writes to the control
latch that occur after the lock
bit has been set to a one, can
only modify the Stop bit. Any
writes to the control latch,
while the RESET input is
asserted, are ignored. RESET
also clears the PW latch.
WR 17 WRITE-a low-to-high transition
on this input, when CHIP
SELECT is low, causes data to
be written to the selected
IXDP610 latch. If SELECT is
low, the data is written to the
pulse width latch. If SELECT is
high, the data is written to the
control latch.
CS
18 CHIP SELECT - this active low
input enables the WRITE input
so that data may be written
into the IXDP610 latch
selected by the SELECT input.
IXDP 610 P I
(Example)
IX
IXYS
DP 610
Digital PWM Controller
Package Type
18-Pin Plastic DIP
P
Temperature Range
Industrial
(-40 to 85
°
C)
I
IXYS
IXDP610PI
相關PDF資料
PDF描述
IXR100 IXR100 - DISCONTINUED PRODUCT. No longer recommended for new design.
IXSA12N60AU1 TRANSISTOR | IGBT | N-CHAN | 600V V(BR)CES | 24A I(C) | TO-263AA
IXSE502PI Servo Encoder
IXSE503PC Servo Encoder
IXSE503PI Servo Encoder
相關代理商/技術參數
參數描述
IXPN4004AR 制造商:UNBRANDED 功能描述:CHARGER, NICAD, CHARGER UPGRADE KIT
IX-POLE-KIT 制造商:PolyPhaser 功能描述:INTERCONNECT KIT
IXR100 制造商:BB 制造商全稱:BB 功能描述:Isolated, Self-Powered, Temperature Sensor Conditioning 4-20mA TWO-WIRE TRANSMITTER
IXRB5-506MINIPACK2 功能描述:IGBT 模塊 MiniPack 2 RoHS:否 制造商:Infineon Technologies 產品:IGBT Silicon Modules 配置:Dual 集電極—發射極最大電壓 VCEO:600 V 集電極—射極飽和電壓:1.95 V 在25 C的連續集電極電流:230 A 柵極—射極漏泄電流:400 nA 功率耗散:445 W 最大工作溫度:+ 125 C 封裝 / 箱體:34MM 封裝:
IXRFD630 制造商:IXYS Corporation 功能描述:DRIVER MOSFET 30A DE275 制造商:IXYS Corporation 功能描述:DRIVER, MOSFET, 30A, DE275
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*