Capacitor Selection The charge pumps operate with 0.1 F (or greater) capacitors for 3.0V ≤ VCC
參數資料
型號: ISL8563ECB
廠商: Intersil
文件頁數: 6/9頁
文件大?。?/td> 0K
描述: XMITTER/RCVR RS562/232 18-SOIC
標準包裝: 40
類型: 收發器
驅動器/接收器數: 2/2
規程: RS232,RS562
電源電壓: 3 V ~ 5.5 V
安裝類型: 表面貼裝
封裝/外殼: 18-SOIC(0.295",7.50mm 寬)
供應商設備封裝: 18-SOIC W
包裝: 管件
6
Capacitor Selection
The charge pumps operate with 0.1
F (or greater)
capacitors for 3.0V
≤ VCC ≤ 5.5V. Increasing the capacitor
values (by a factor of 2) reduces ripple on the transmitter
outputs and slightly reduces power consumption. C2, C3, and
C4 can be increased without increasing C1’s value, however,
do not increase C1 without also increasing C2, C3, and C4 to
maintain the proper ratios (C1 to the other capacitors).
When using minimum required capacitor values, make sure
that capacitor values do not degrade excessively with
temperature. If in doubt, use capacitors with a larger nominal
value. The capacitor’s equivalent series resistance (ESR)
usually rises at low temperatures and it influences the
amount of ripple on V+ and V-.
Power Supply Decoupling
In most circumstances a 0.1
F bypass capacitor is
adequate. In applications that are particularly sensitive to
power supply noise, decouple VCC to ground with a
capacitor of the same value as the charge-pump capacitor C1.
Connect the bypass capacitor as close as possible to the IC.
Operation Down to 2.7V
ISL8563E transmitter outputs meet RS-562 levels (±3.7V), at
the full data rate, with VCC as low as 2.7V. RS-562 levels
typically ensure interoperability with RS-232 devices.
Transmitter Outputs When Exiting
Powerdown
Figure 6 shows the response of two transmitter outputs
when exiting powerdown mode. As they activate, the two
transmitter outputs properly go to opposite RS-562/232
levels, with no glitching, ringing, nor undesirable transients.
Each transmitter is loaded with 3k
in parallel with 2500pF.
Note that the transmitters enable only when the magnitude
of the supplies exceed approximately 3V.
High Data Rates
The ISL8563E maintains the RS-232 ±5V minimum
transmitter output voltages even at high data rates. Figure 7
details a transmitter loopback test circuit, and Figure 8
illustrates the loopback test result at 120kbps. For this test,
all transmitters were simultaneously driving RS-232 loads in
parallel with 1000pF, at 120kbps. Figure 9 shows the
loopback results for a single transmitter driving 1000pF and
an RS-232 load at 250kbps. The static transmitters were
also loaded with an RS-232 receiver.
FIGURE 4. POWER DRAIN THROUGH POWERED DOWN
PERIPHERAL
OLD
VCC
POWERED
GND
SHDN = GND
VCC
Rx
Tx
VCC
CURRENT
VOUT = VCC
FLOW
RS-562/232 CHIP
DOWN
UART
FIGURE 5. DISABLED RECEIVERS PREVENT POWER DRAIN
ISL8563E
TRANSITION
RX
TX
R2OUT
T1IN
VCC
TO
R2IN
T1OUT
VOUT = HI-Z
POWERED
SHDN = GND, EN = VCC
DETECTOR
DOWN
UART
WAKE-UP
LOGIC
TIME (20
s/DIV)
T1
T2
2V/DIV
5V/DIV
VCC = +3.3V
SHDN
FIGURE 6. TRANSMITTER OUTPUTS WHEN EXITING
POWERDOWN
C1 - C4 = 0.1
F
ISL8563E
相關PDF資料
PDF描述
PI90LV018AWE IC LVDS DIFF LINE RCVR HS 8-SOIC
PI90LV018AUEX IC LVDS DIFF LINE RCVR HS 8-MSOP
ICS932S890CKLFT IC CLK CHIP EXPRESS 72MLF
ICS844204BK-245LFT IC CLK SYNTHESIZER 4LVDS 32VFQFN
VE-2NZ-MW-S CONVERTER MOD DC/DC 2V 40W
相關代理商/技術參數
參數描述
ISL8563ECB-T 功能描述:XMITTER/RCVR RS562/232 18-SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器,接收器,收發器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:25 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:4.5 V ~ 5.5 V 安裝類型:通孔 封裝/外殼:16-DIP(0.300",7.62mm) 供應商設備封裝:16-PDIP 包裝:管件
ISL8563ECP 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Intersil Corporation 功能描述:
ISL8563EIB 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Intersil Corporation 功能描述:
ISL8563EIP 制造商:Rochester Electronics LLC 功能描述:- Bulk
ISL8563IB 制造商:Rochester Electronics LLC 功能描述:RS562 3V 2D/2R SHUTDOWN 18SOIC IND - Bulk