參數資料
型號： ISL6561CR
廠商： INTERSIL CORP
元件分類： 穩壓器
英文描述： Multi-Phase PWM Controller with Precision Rds(on) or DCR Differential Current Sensing for VR10.X Application
中文描述： SWITCHING CONTROLLER, 1500 kHz SWITCHING FREQ-MAX, PQCC40
封裝： 6 X 6 MM, PLASTIC, MO-220VJJD-2, MLFP, QFN-40
文件頁數： 19/26頁
文件大?。?/td> 782K
代理商： ISL6561CR
19
FN9098.5
May 12, 2005
command the lower MOSFETs to turn on. The ISL6561 will
continue to protect the load in this fashion as long as the
overvoltage condition recurs.
Simultaneous to the protective action of the PWM outputs,
the OVP pin pulls to VCC delivering up to 100mA to the gate
of a crowbar MOSFET or SCR placed either on the input rail
or the output rail. Turning on the MOSFET or SCR collapses
the power rail and causes a fuse placed further up stream to
will not overheat before the fuse blows. The OVP pin is
tolerant to 12V (see
Absolute Maximum Ratings
external resistor pull up can be used to augment the driving
capability. If using a pull up resistor in conjunction with the
internal overvoltage protection function, care must be taken
to avoid nuisance trips that could occur when VCC is below
2V. In that case, the controller is incapable of holding OVP
low.
Once an overvoltage condition is detected, normal PWM
operation ceases until the ISL6561 is reset. Cycling the
voltage on EN or ENLL or VCC below the POR-falling
threshold will reset the controller. Cycling the VID codes will
not reset the controller.
Overcurrent Protection
ISL6561 has two levels of overcurrent protection. Each
phase is protected from a sustained overcurrent condition on
a delayed basis, while the combined phase currents are
protected on an instantaneous basis.
In instantaneous protection mode, the ISL6561 takes
advantage of the proportionality between the load current
and the average current, I
AVG
to detect an overcurrent
condition. See the
Channel-Current Balance
section for
more detail on how the average current is measured. The
average current is continually compared with a constant
100
μ
A reference current as shown in Figure 11. Once the
average current exceeds the reference current, a comparator
triggers the converter to shutdown.
In individual overcurrent protection mode, the ISL6561
continuously compares the current of each channel with the
same 100
μ
A reference current. If any channel current
exceeds the reference current continuously for eight
consecutive cycles, the comparator triggers the converter to
shutdown.
At the beginning of overcurrent shutdown, the controller
places all PWM signals in a high-impedance state
commanding the Intersil MOSFET driver ICs to turn off both
upper and lower MOSFETs. The system remains in this
state a period of 4096 switching cycles. If the controller is still
enabled at the end of this wait period, it will attempt a soft
start. If the fault remains, trip-retry cycles continue
indefinitely (as shown in Figure 12) until either controller is
disabled or the fault is cleared. Note that the energy
delivered during trip-retry cycling is much less than during
full-load operation, so there, there is no thermal hazard
during this kind of operation.
General Design Guide
This design guide is intended to provide a high-level
explanation of the steps necessary to create a multi-phase
power converter. It is assumed that the reader is familiar with
many of the basic skills and techniques referenced below. In
addition to this guide, Intersil provides complete reference
designs that include schematics, bills of materials, and
example board layouts for all common microprocessor
applications.
Power Stages
The first step in designing a multi-phase converter is to
determine the number of phases. This determination
depends heavily on the cost analysis which in turn depends
on system constraints that differ from one design to the next.
Principally, the designer will be concerned with whether
components can be mounted on both sides of the circuit
board; whether through-hole components are permitted; and
the total board space available for power-supply circuitry.
Generally speaking, the most economical solutions are
those in which each phase handles between 15 and 20A. All
surface-mount designs will tend toward the lower end of this
current range. If through-hole MOSFETs and inductors can
be used, higher per-phase currents are possible. In cases
where board space is the limiting constraint, current may be
pushed above 30A per phase, but these designs require
heat sinks and forced air to cool the MOSFETs, inductors
and heat-dissipating surfaces.
MOSFETs
The choice of MOSFETs depends on the current each
MOSFET will be required to conduct; the switching frequency;
the capability of the MOSFETs to dissipate heat; and the
availability and nature of heat sinking and air flow.
0A
0V
2ms/DIV
OUTPUT CURRENT, 50A/DIV
FIGURE 12. OVERCURRENT BEHAVIOR IN HICCUP MODE.
F
SW
= 500kHz
OUTPUT VOLTAGE,
500mV/DIV
ISL6561
相關PDF資料
PDF描述
ISL6561CRZ Multi-Phase PWM Controller with Precision Rds(on) or DCR Differential Current Sensing for VR10.X Application
ISL6561 Multi-Phase PWM Controller with Precision rDS(ON) or DCR Differential Current Sensing for VR10.X Application(帶有精密rDS(ON)或DCR差分電流感應的VR10.X專用多相PWM控制器)
ISL6561CRZ-T Multi-Phase PWM Controller with Precision Rds(on) or DCR Differential Current Sensing for VR10.X Application
ISL6561CRZA Multi-Phase PWM Controller with Precision Rds(on) or DCR Differential Current Sensing for VR10.X Application
ISL6561IR Multi-Phase PWM Controller with Precision Rds(on) or DCR Differential Current Sensing for VR10.X Application
相關代理商/技術參數
參數描述
ISL6561CR-T 功能描述:IC CTRLR PWM MULTIPHASE 40-QFN RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,000 系列:- 應用:電源，ICERA E400，E450 輸入電壓:4.1 V ~ 5.5 V 輸出數:10 輸出電壓:可編程 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:42-WFBGA，WLCSP 供應商設備封裝:42-WLP 包裝:帶卷 (TR)
ISL6561CRZ 功能描述:IC CTRLR PWM MULTIPHASE 40-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:43 系列:- 應用:控制器，Intel VR11 輸入電壓:5 V ~ 12 V 輸出數:1 輸出電壓:0.5 V ~ 1.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-QFN（7x7） 包裝:管件
ISL6561CRZ 制造商:Intersil Corporation 功能描述:Pulse Width Modulation (PWM) Controller
ISL6561CRZA 功能描述:IC CTRLR PWM MULTIPHASE 40-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:43 系列:- 應用:控制器，Intel VR11 輸入電壓:5 V ~ 12 V 輸出數:1 輸出電壓:0.5 V ~ 1.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-QFN（7x7） 包裝:管件
ISL6561CRZA-T 功能描述:IC CTRLR PWM MULTIPHASE 40-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:43 系列:- 應用:控制器，Intel VR11 輸入電壓:5 V ~ 12 V 輸出數:1 輸出電壓:0.5 V ~ 1.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-QFN（7x7） 包裝:管件
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*