- 您現在的位置：買賣IC網 > PDF目錄353714 > ISL6537ACRZ-T (INTERSIL CORP) ACPI Regulator/Controller for Dual Channel DDR Memory Systems PDF資料下載
參數資料
| 型號： | ISL6537ACRZ-T |
| 廠商： | INTERSIL CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | ACPI Regulator/Controller for Dual Channel DDR Memory Systems |
| 中文描述： | 3.3 A DUAL SWITCHING CONTROLLER, 280 kHz SWITCHING FREQ-MAX, PQCC28 |
| 封裝： | 6 X 6 MM, ROHS COMPLIANT, PLASTIC, MO-220VJJC, QFN-28 |
| 文件頁數： | 2/15頁 |
| 文件大?。?/td> | 488K |
| 代理商： | ISL6537ACRZ-T |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁
10
FN9143.3
The overcurrent function will trip at a peak inductor current
(IPEAK) determined by:
where IOCSET is the internal OCSET current source (20A
typical). The OC trip point varies mainly due to the MOSFET
rDS(ON) variations. To avoid overcurrent tripping in the
normal operating load range, find the ROCSET resistor from
the equation above with:
1. The maximum rDS(ON) at the highest junction
temperature.
2. The minimum IOCSET from the specification table.
3. Determine IPEAK for
,
where
I is the output inductor ripple current.
For an equation for the ripple current see the section under
component guidelines titled ‘Output Inductor Selection’.
A small ceramic capacitor should be placed in parallel with
ROCSET to smooth the voltage across ROCSET in the
presence of switching noise on the input voltage.
Thermal Protection (S0/S3 State)
If the ISL6537A IC junction temperature reaches a nominal
temperature of 140°C, all regulators will be disabled. The
ISL6537A will not re-enable the outputs until the junction
temperature drops below 110°C and either the bias voltage is
toggled in order to initiate a POR or the SLP_S5 signal is
forced LOW and then back to HIGH.
Shoot-Through Protection
A shoot-through condition occurs when both the upper and
lower MOSFETs are turned on simultaneously, effectively
shorting the input voltage to ground. To protect from a shoot-
through condition, the ISL6537A incorporates specialized
circuitry on the VDDQ regulator which insures that
complementary MOSFETs are not ON simultaneously.
The adaptive shoot-through protection utilized by the VDDQ
regulator looks at the lower gate drive pin, LGATE, and the
upper gate drive pin, UGATE, to determine whether a
MOSFET is ON or OFF. If the voltage from UGATE or from
LGATE to GND is less than 0.8V, then the respective
MOSFET is defined as being OFF and the other MOSFET is
allowed to turned ON. This method allows the VDDQ
regulator to both source and sink current.
Since the voltage of the MOSFET gates are being measured
to determine the state of the MOSFET, the designer is
encouraged to consider the repercussions of introducing
external components between the gate drivers and their
respective MOSFET gates before actually implementing
such measures. Doing so may interfere with the shoot-
through protection.
Application Guidelines
Layout Considerations
Layout is very important in high frequency switching
converter design. With power devices switching efficiently at
250kHz, the resulting current transitions from one device to
another cause voltage spikes across the interconnecting
impedances and parasitic circuit elements. These voltage
spikes can degrade efficiency, radiate noise into the circuit,
and lead to device overvoltage stress. Careful component
layout and printed circuit board design minimizes these
voltage spikes.
As an example, consider the turn-off transition of the control
MOSFET. Prior to turn-off, the MOSFET is carrying the full
load current. During turn-off, current stops flowing in the
MOSFET and is picked up by the lower MOSFET. Any
parasitic inductance in the switched current path generates a
large voltage spike during the switching interval. Careful
component selection, tight layout of the critical components,
and short, wide traces minimizes the magnitude of voltage
spikes.
There are two sets of critical components in the ISL6537A
switching converter. The switching components are the most
critical because they switch large amounts of energy, and
therefore tend to generate large amounts of noise. Next are
the small signal components which connect to sensitive
nodes or supply critical bypass current and signal coupling.
A multi-layer printed circuit board is recommended. Figure 2
shows the connections of the critical components in the
converter. Note that capacitors CIN and COUT could each
represent numerous physical capacitors. Dedicate one solid
layer, usually a middle layer of the PC board, for a ground
plane and make all critical component ground connections
with vias to this layer. Dedicate another solid layer as a
power plane and break this plane into smaller islands of
common voltage levels. Keep the metal runs from the
PHASE terminals to the output inductor short. The power
plane should support the input power and output power
nodes. Use copper filled polygons on the top and bottom
circuit layers for the phase nodes. Use the remaining printed
circuit layers for small signal wiring. The wiring traces from
the GATE pins to the MOSFET gates should be kept short
and wide enough to easily handle the 1A of drive current.
In order to dissipate heat generated by the internal VTT
LDO, the ground pad, pin 29, should be connected to the
internal ground plane through at least four vias. This allows
the heat to move away from the IC and also ties the pad to
the ground plane through a low impedance path.
The switching components should be placed close to the
ISL6537A first. Minimize the length of the connections
between the input capacitors, CIN, and the power switches
by placing them nearby. Position both the ceramic and bulk
input capacitors as close to the upper MOSFET drain as
IPEAK
IOCSET x ROCSET
rDS ON
()
-----------------------------------------------------
=
IPEAK IOUT MAX
()
I
()
2
----------
+
>
ISL6537A
相關PDF資料 |
PDF描述 |
|---|---|
| ISL4260EIR-T | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
| ISL4270EIR-T | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
| ISL6410IUZ-T | Single Synchronous Buck Regulators with Integrated FET |
| ISL6410IR | Single Synchronous Buck Regulators with Integrated FET |
| ISL6412IRZ | Triple Output, Low-Noise LDO Regulator with Integrated Reset Circuit |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6537ACRZ-TR5160 | 功能描述:IC REG/CTRLR ACPI DUAL DDR 28QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:- 應用說明:Ultrasound Imaging Systems Application Note 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:37 系列:- 應用:醫療用超聲波成像，聲納 電流 - 電源:- 電源電壓:2.37 V ~ 6 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:56-WFQFN 裸露焊盤 供應商設備封裝:56-TQFN-EP（8x8） 包裝:管件 |
| ISL6537CR | 功能描述:IC REG/CTRLR ACPI DUAL DDR 28QFN RoHS:否 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:- 應用說明:Ultrasound Imaging Systems Application Note 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:37 系列:- 應用:醫療用超聲波成像，聲納 電流 - 電源:- 電源電壓:2.37 V ~ 6 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:56-WFQFN 裸露焊盤 供應商設備封裝:56-TQFN-EP（8x8） 包裝:管件 |
| ISL6537CR-T | 功能描述:IC REG/CTRLR ACPI DUAL DDR 28QFN RoHS:否 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:- 應用說明:Ultrasound Imaging Systems Application Note 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:37 系列:- 應用:醫療用超聲波成像，聲納 電流 - 電源:- 電源電壓:2.37 V ~ 6 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:56-WFQFN 裸露焊盤 供應商設備封裝:56-TQFN-EP（8x8） 包裝:管件 |
| ISL6537CRZ | 功能描述:IC REG/CTLR ACPI DUAL DDR 28QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 應用:熱電冷卻器 電流 - 電源:- 電源電壓:3 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.173"，4.40mm 寬）裸露焊盤 供應商設備封裝:28-TSSOP 裸露焊盤 包裝:管件 產品目錄頁面:1410 (CN2011-ZH PDF) |
| ISL6537CRZA-TR5160 | 功能描述:IC REG/CTRLR ACPI DUAL DDR 28QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:- 應用說明:Ultrasound Imaging Systems Application Note 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:37 系列:- 應用:醫療用超聲波成像，聲納 電流 - 電源:- 電源電壓:2.37 V ~ 6 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:56-WFQFN 裸露焊盤 供應商設備封裝:56-TQFN-EP（8x8） 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。