- 您現在的位置：買賣IC網 > PDF目錄296253 > ISL6406IR (INTERSIL CORP) Quadruple 2-Input Positive-NAND Gates 14-SO -40 to 85 PDF資料下載
參數資料
| 型號： | ISL6406IR |
| 廠商： | INTERSIL CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | Quadruple 2-Input Positive-NAND Gates 14-SO -40 to 85 |
| 中文描述： | SWITCHING CONTROLLER, 770 kHz SWITCHING FREQ-MAX, PQCC16 |
| 封裝： | PLASTIC, MO-220-VHHB, MLFP, QFN-16 |
| 文件頁數： | 18/18頁 |
| 文件大小： | 380K |
| 代理商： | ISL6406IR |
9
FN9073.7
January 16, 2007
.
Frequency Synchronization and Enable
The external frequency synchronization and enable
functions are combined in SYNC/EN pin. This pin is TTL
compatible for VCC = 3.3V or 5V. The device is disabled if
the input to this pin is TTL LOW for more than 40
μs (typ.); it
is enabled if the input is TTL HIGH without delay. When
disabling the IC, the charge pump is turned off and the
BOOT pin is left charged at ~5V. In some cases this charge
will inadvertant leak through the upper gate driver and can
possibly turn on the upper FET. To avoid this, it is
recommended that a 1M
Ω ‘bleed’ resistor be connected from
the BOOT pin to GND. This resistor is shown in the typical
The SYNC/EN pin is monitored by the internal timer. The
timer allows SYNC pulses (TTL LOW level) to pass through,
as long as the pulses are shorter than 22
μs. The minimum
SYNC pulse width is 40ns (typ.).
The oscillator can SYNC to an external frequency of
between 1.1 times and 2.0 times the free-running frequency.
Loop acquisition time is about 200 clock cycles. The timing
resistor (RT) is always required, regardless of whether
SYNC pulses are being used or not.
For instance, if RT is selected such that the switching
frequency is 100kHz then the ISL6406 can be synchronized
to a switching frequency from 110kHz to 200kHz.
Overcurrent Protection
The overcurrent function protects the converter from a
shorted output by using the upper MOSFET on-resistance,
rDS(ON), to monitor the current. This method enhances the
converter’s efficiency and reduces cost by eliminating a
current sensing resistor. The over current function cycles the
soft-start function in a hiccup mode to provide fault
protection. A resistor (ROCSET) programs the over current
trip level (see Typical Application diagrams). An internal
20A (typical) current sink develops a voltage across
ROCSET that is referenced to VIN. When the voltage across
the upper MOSFET (also referenced to VIN) exceeds the
voltage across ROCSET, the over current function initiates a
soft-start sequence.
Figure 5 illustrates the protection feature responding to an
overcurrent event. At time t0, an overcurrent condition is
sensed across the upper MOSFET. As a result, the regulator
is quickly shutdown and the internal soft-start function begins
producing soft-start ramps. The delay interval seen by the
output is equivalent to three soft-start cycles. The fourth
internal soft-start cycle initiates a normal soft-start ramp of the
output, at time t1. The output is brought back into regulation
by time t2, as long as the overcurrent event has cleared. Had
the cause of the over current still been present after the delay
interval, the over current condition would be sensed and the
regulator would be shut down again for another delay interval
of three soft-start cycles. The resulting hiccup mode style of
protection would continue to repeat indefinitely.
The overcurrent function will trip at a peak inductor current
where IOCSET is the internal OCSET current source (20A
typical). The OC trip point varies mainly due to the MOSFET
rDS(ON) variations. To avoid overcurrent tripping in the
FIGURE 4. OUTPUT VOLTAGE SELECTION
+
R1
COUT
+3.3V
VOUT
R4
LOUT
ISL6406,
C4
Q1
FB
UGATE
VCC
BOOT
COMP
D1
R2
C2
C1
R3
C3
PHASE
LGATE
Q2
CPVOUT
VIN
FIGURE 5. OVERCURRENT PROTECTION RESPONSE
0V
TIME
VOUT (2.5V)
t1
t0
t2
INTERNAL SOFT-START FUNCTION
DELAY INTERVAL
I
PEAK
I
OCSET
() R
OCSET
()
r
DS ON
()
--------------------------------------------------------
=
(EQ. 3)
ISL6406
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6406IV | Quadruple 2-Input Positive-NAND Gates 14-SO -40 to 85 |
| ISL6410IRZ | Quadruple 2-Input Positive-NAND Gates 14-TSSOP -40 to 85 |
| ISL6410IRZ-T | Quadruple 2-Input Positive-NAND Gates 14-TSSOP -40 to 85 |
| ISL6410IRZ-T5K | Single Synchronous Buck Regulators with Integrated FET |
| ISL6410IRZ-TK | Quadruple 2-Input Positive-NAND Gates 14-TSSOP -40 to 85 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6406IR-T | 功能描述:IC REG CTRLR BUCK PWM VM 16-QFN RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,000 系列:- PWM 型:電壓模式 輸出數:1 頻率 - 最大:1.5MHz 占空比:66.7% 電源電壓:4.75 V ~ 5.25 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 85°C 封裝/外殼:40-VFQFN 裸露焊盤 包裝:帶卷 (TR) |
| ISL6406IRZ | 功能描述:IC REG CTRLR BUCK PWM VM 16-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) |
| ISL6406IRZ-T | 功能描述:IC REG CTRLR BUCK PWM VM 16-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) |
| ISL6406IV | 功能描述:IC REG CTRLR BUCK PWM VM 16TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,000 系列:- PWM 型:電壓模式 輸出數:1 頻率 - 最大:1.5MHz 占空比:66.7% 電源電壓:4.75 V ~ 5.25 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 85°C 封裝/外殼:40-VFQFN 裸露焊盤 包裝:帶卷 (TR) |
| ISL6406IV-T | 功能描述:IC REG CTRLR BUCK PWM VM 16TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,000 系列:- PWM 型:電壓模式 輸出數:1 頻率 - 最大:1.5MHz 占空比:66.7% 電源電壓:4.75 V ~ 5.25 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 85°C 封裝/外殼:40-VFQFN 裸露焊盤 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。