FN6314.2 July 15, 2010 If full industrial temperature compensation is desired in an ISL1219 circuit, then both the DTR and ATR registers will n" />
參數資料
型號： ISL1219IUZ-T
廠商： Intersil
文件頁數： 15/24頁
文件大?。?/td> 0K
描述： IC RTC LP BATT BACK SRAM 10MSOP
產品培訓模塊： Solutions for Industrial Control Applications
標準包裝： 2,500
類型： 時間事件記錄器
特點： 警報器，閏年，SRAM
存儲容量： 2B
時間格式： HH:MM:SS（12/24 小時）
數據格式： YY-MM-DD-dd
接口： I²C，2 線串口
電源電壓： 2.7 V ~ 5.5 V
電壓 - 電源，電池： 1.8 V ~ 5.5 V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 10-TFSOP，10-MSOP（0.118"，3.00mm 寬）
供應商設備封裝： 10-MSOP
包裝： 帶卷 (TR)
22
FN6314.2
July 15, 2010
If full industrial temperature compensation is desired in an
ISL1219 circuit, then both the DTR and ATR registers will
need to be utilized (total correction range = -94 to +140ppm).
A system to implement temperature compensation would
consist of the ISL1219, a temperature sensor, and a
microcontroller. These devices may already be in the system
so the function will just be a matter of implementing software
and performing some calculations. Fairly accurate
temperature compensation can be implemented just by using
the crystal manufacturer’s specifications for the turnover
temperature T0 and the drift coefficient (β). The formula for
calculating the oscillator adjustment necessary is:
Adjustment (ppm) = (T – T0)2 * β
Once the temperature curve for a crystal is established, then
the designer should decide at what discrete temperatures
the compensation will change. Since drift is higher at
extreme temperatures, the compensation may not be
needed until the temperature is greater than +20°C from T0.
A sample curve of the ATR setting vs. Frequency Adjustment
for the ISL1219 and a typical RTC crystal is given in
Figure 21. This curve may vary with different crystals, so it is
good practice to evaluate a given crystal in an ISL1219
circuit before establishing the adjustment values.
This curve is then used to figure what ATR and DTR settings
are used for compensation. The results would be placed in a
lookup table for the microcontroller to access.
Layout Considerations
The crystal input at X1 has a very high impedance, and
oscillator circuits operating at low frequencies such as
32.768kHz are known to pick up noise very easily if layout
precautions are not followed. Most instances of erratic clocking
or large accuracy errors can be traced to the susceptibility of
the oscillator circuit to interference from adjacent high speed
clock or data lines. Careful layout of the RTC circuit will avoid
noise pickup and insure accurate clocking.
Figure 22 shows a suggested layout for the ISL1219 device
using a surface mount crystal. Two main precautions should
be followed:
1. Do not run the serial bus lines or any high speed logic
lines in the vicinity of the crystal. These logic level lines
can induce noise in the oscillator circuit to cause
misclocking.
2. Add a ground trace around the crystal with one end
terminated at the chip ground. This will provide termination
for emitted noise in the vicinity of the RTC device.
In addition, it is a good idea to avoid a ground plane under
the X1 and X2 pins and the crystal, as this will affect the load
capacitance and therefore the oscillator accuracy of the
circuit. If the ~IRQ/FOUT pin is used as a clock, it should be
routed away from the RTC device as well. The traces for the
VBAT and VDD pins can be treated as a ground, and should
be routed around the crystal.
Super Capacitor Backup
The ISL1219 device provides a VBAT pin which is used for a
battery backup input. A Super Capacitor can be used as an
alternative to a battery in cases where shorter backup times
are required. Since the battery backup supply current
required by the ISL1219 is extremely low, it is possible to get
months of backup operation using a Super Capacitor.
Typical capacitor values are a few F to 1 Farad or more
depending on the application.
If backup is only needed for a few minutes, then a small
inexpensive electrolytic capacitor can be used. For extended
periods, a low leakage, high capacity Super Capacitor is the
TEMPERATURE (°C)
-160.0
-140.0
-120.0
-100.0
-80.0
-60.0
-40.0
-20.0
0.0
-40 -30 -20 -10 0 1020 30 40 50607080
PP
M
FIGURE 20. RTC CRYSTAL TEMPERATURE DRIFT
-40.0
-30.0
-20.0
-10.0
0.0
10.0
20.0
30.0
40.0
50.0
60.0
70.0
80.0
90.0
0
5 10 15 20 25 30 35 40 45 50 55 60
ATR SETTING
PP
M
ADJUSTME
N
T
FIGURE 21. ATR SETTING vs OSCILLATOR FREQUENCY
ADJUSTMENT
FIGURE 22. SUGGESTED LAYOUT FOR ISL1219 AND
CRYSTAL
ISL1219
ISL1219
相關PDF資料
PDF描述
ISL1220IUZ IC RTC LP BATT BACK SRAM 10MSOP
ISL1221IUZ IC RTC LP BATT BACK SRAM 10MSOP
ISL26134AVZ IC ADC 24BIT SRL 80SPS 28TSSOP
ISL26319FVZ-T7A IC ADC 12BIT SRL/SPI 16TSSOP
ISL26329FVZ IC ADC 12BIT SPI/SRL 16-TSSOP
相關代理商/技術參數
參數描述
ISL1220 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:I2C㈢ Real Time Clock/Calendar with Frequency Output
ISL1220IUZ 功能描述:實時時鐘 REAL TIME CLKRTC IN RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube
ISL1220IUZ-T 功能描述:實時時鐘 REAL TIME CLKRTC IN RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube
ISL1221 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Low Power RTC with Battery Backed
ISL1221IUZ 功能描述:實時時鐘 REAL TIME CLKRTC IN RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*